Denon AVR-5800 - Manual (Page 7)

7
Connecting video components
• To connect the video signal, connect using a 75
Ω
/ohms video signal cable cord. Using an improper cable can result in a drop in picture quality.
• When making connections, also refer to the operating instructions of the other components.
CONPONENT VIDEO
R
L
R
L
R
L
R
L
SPEAKER SYSTEMS
SPEAKER IMPEDANCE
FRONT, CENTER, SURROUND BACK
SURROUND A OR B / 6 16 Ω
A + B / 8 16 Ω
A + B / 6 16 Ω
AC OUTLETS
SWITCHED TOTAL 120W (1A.) MAX.
AC 120V 60Hz
MULTI
/ SB
SURR.-B
SURR.-A
FRONT
EFFECT
/ SB
L
L
L
L
L
IN DVD
C B C R Y
VDP TV DBS / V. AUX VCR-1 VCR-2 VCR-3 VCR-1 VCR-2 VCR-3
1 2 SAT 1
VIDEO
S-VIDEO
OUT
OUT OUT IN
IN
IN EXT. IN-1
SW SW
1 2
COAXIAL
(REMOTE CONTROL)
ROOM TO ROOM POWER
AMP
RS-232C OPTICAL
DIGITAL
3 1 2 3 4 5 6 5 6
SW
EXT. IN-2 PRE OUT OUT OUT
OUT
IN OUT
AUDIO
IN
MONITOR DVD
VDP TV
DBS /
V. AUX VCR-1 VCR-2 VCR-3 VCR-1 VCR-2 VCR-3 SAT
MD /
AC IN
TAPE-2
CDR /
TAPE-1
MD / MULTI ZONE
TAPE-2 1 2
CDR /
TAPE-1
DVD
CENTER SURR. EFFECT FRONT CENTER SURR. EFFECT FRONT
DOLBY DIGITAL RF
CENTER SURR.
EFFECT
/ SB FRONT PHONO
CD
MULTI ZONE
IN TV
C
B C R Y
IN DBS / SAT
C B C R Y
OUT MONITOR
C B C R Y
OUT OUT IN
IN
VIDEO
L
R
L
R
L
R
L
R
R L
R
L
R OUT IN
AUDIO VIDEO
OUT IN
L R L
R L R L
R OUT IN
AUDIO VIDEO
OUT IN
L R L
R L R L
R OUT
VIDEO
OUT
L
AUDIO
L R
R OUT
VIDEO
OUT
L
AUDIO
L R
RF OUT COAXIAL OPTICAL
OUTPUT
TV or DBS tuner
LD player, CDV player, etc.
Monitor TV
Connecting a TV/DBS tuner
TV/DBS
• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the
(yellow) TV/DBS IN jack using a
75 Ω /ohms video coaxial pin plug cord.
• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to the TV/DBS IN jacks using pin plug
cords.
AUDIO
VIDEO
Connecting a video disc player VDP
VDP
• Connect the video disc player’s video output jack (VIDEO OUTPUT) to the
(yellow) VDP IN jack using a 75 Ω /ohms video coaxial pin plug cord.
• Connect the video disc player’s analog audio output jacks (ANALOG AUDIO
OUTPUT) to the VDP IN jacks using pin plug cords.
• A DVD player can be connected to the DVD jacks in the same way.
• It is also possible to connect a video disc player, DVD player, video camcorder,
game machine, etc., to the V.AUX jacks.
AUDIO
VIDEO
MONITOR OUT
• Connect the TV’s video input
jack (VIDEO INPUT) to the
MONITOR OUT jack
using a 75 Ω /ohms video
coaxial pin plug cord.
• The monitor TV can also be
connected in the same way
to the VIDEO MONITOR
OUT-2 jack. Note, however,
that the AVR-5800’s on-
screen display signals are
not output from this jack.
(See page 30.)
VIDEO
Note on connecting the digital
input jacks
• Only audio signals are input to the
digital input jacks. For details, see
page 6.
LD player or other component
equipped with digital output jacks
Video deck 2
Video deck 1
• There are three sets of video deck (VCR) jacks, so three video decks can be connected for simultaneous recording or video copying.
Video input/output connections:
• Connect the video deck’s video output jack (VIDEO OUT) to the
(yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the
(yellow) VCR-1 OUT jack using 75 Ω /ohms video coaxial pin plug cords.
Connecting the audio output jacks
• Connect the video deck’s audio output jacks (AUDIO OUT) to the
VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR-1
OUT jacks using pin plug cords.
Connect the another video deck to the VCR-2 or VCR-3 jacks in the same way.
AUDIO AUDIO
VIDEO VIDEO
Connecting a video decks
LD player or other component equipped
with a Dolby Digital RF output jacks
NOTES:
Video output connections for LD players equipped with Dolby Digital-RF (AC-3 RF) output jacks.
• To connect an Dolby Digital AC-3 compatible LD player to the Dolby Digital-RF (AC-3 RF) jacks,
connect the player’s video outputs to this unit’s VDP input jacks.
• When the Dolby Digital-RF (AC-3 RF) input selector button on the AVR-5800 is pressed, the
picture switches to the signals input to the VDP input jacks.