Smithco Spray Star 1000 (sn 100199 – 100223) Parts & Service Manual - Manual (Page 105)

103
Accessories
HOSE REEL PLUMBING PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 15-552 Manifold Ball Valve 1
2* 16-851 Close Nipple 1" (1006 and 1008 only) 2
3* 16-154 Fitting 3 /
4
MPT x 3 /
4
HB 1
4* 16-859 Ball Valve 3 /
4
Brass 1
5* 16-158 Close Nipple 3 /
4
" 2
6* 16-163 Reducer Bushing 1 x 3 /
4 (1006 and 1008 only) 1
7* 16-183 Tee FPT 1 x 1 x 1 (1006 and 1008 only) 1
8 15-531 Pressure Regulating Valve (1006) 1
16-886 Motorized Control Valve (1002) 1
9 16-164 Elbow 1" MPT x 1" HB 1
10 16-151 Elbow FPT 3 /
4
x 3 /
4
1
11* 16-157 Tee FPT 3 /
4
x 3 /
4
x 3 /
4 (1004 only) 1
12 16-153 Elbow 3 /
4
" MPT x 3 /
4
" HB 1
13 16-172 Nylon Nipple 3 /
4
x 3 1 /
2
1
14 16-162 Hex Plug 1
15 16-524 Motorized Control Valve 1
* 10-107 Hose Reel Mounting Kit (includes only (1) 16-851 Close Nipple)
HOSE REEL MOUNTING INSTRUCTIONS
1. Wear protective clothing when draining the tank and taking apart the lines.
2. Drain tank and spray system in a safe and approved method insuring that no chemical or water remain in
tank as you will be taking apart lines.
3. Remove key from ignition, set park brake and block wheels.
4. Remove square rubber covers on boom carriers.
5. Place hose reel bracket inside the boom carrier tubes with arms pointing toward front of machine..
6. Lower bracket until top hole in bracket lines up with hole in upright. Use four 3 /
8
- 16 x 3 3 /
4
bolts and four
3 /
8
- 16 lock nuts with nuts on inside of uprights.
7. Put hose reel on hose reel bracket with fitting on left side of machine. Use four bolts 5 /
16
- 18 x 1 1 /
2
and
four 5 /
16
- 18 lock nuts to hold in place. Tighten bolts.
8. Put 18-249 barb fitting into hose reel.
9. For 1006 & 1002 System: Remove pressure regulating valve or motorized control valve from manifold ball
valve . Use a 1" close nipple on each side of the tee. Place reducer bushing , 3 /
4
close nipple, ball valve,
and hose barb into tee pointing upward.
10. For 1004 System: From the back of the machine remove the two elbows at the end of the spray fittings.
Insert the 3 /
4
" tee pointing toward the back of the machine. Insert the 3 /
4
" hose barb elbow into the middle
of the tee. This goes to the right boom section. Place a 3 /
4
" close nipple into the open end of the tee and
add the 3 /
4
" FPT elbow pointing upward. Insert the 3 /
4
" close nipple, ball valve, and hose barb.
11. Use 8887-46 hose to connect reel to ball valve, clamp with 18-040 hose clamps.
12. Use 22-075 cable ties to tie hose to main feed hose.
(Continued on next page)