Montigo H38DF-CLCR - Manual (Page 17)

Page 17 XG0213 - 150204.2
H*38DF-CLCR Corner Gas Fireplace
Installation
A - Termination PTO4 (3" Length)
PTO4F (3" Length)
PVTKK1SS
B - Frame Kits MSR (Stucco Frame)
MOSR (Stucco Frame)
BSR-4 (4" Brick Frame)
BSR-6 (6" Brick Frame)
C - Flex Sections PFL - 1 (12" f/f Section)
PFL - 18 (18" f/f Section)
PFL - 2 (24" f/f Section)
PFL - 3 (36" f/f Section)
PFL - 4 (48" f/f Section)
PFL - 6 (72" f/f Section)
D - Rigid Sections PXT - 5 (5" f/f Section)
PXT - 10 (10" f/f Section)
PXT - 20 (20" f/f Section)
PEXT - 1 (12" f/m Section)
PEXT - 2 (24" f/m Section)
PEXT - 3 (36" f/m Section)
PEXT - 4 (48" f/m Section)
PEXT - 6 (72" f/m Section)
E - Elbows PEL-90MM (m/m 90º Elbow)
PEL-90FF ( f/f 90º Elbow)
PEL-90FM ( f/m 90º Elbow)
PEL-45FM ( f/m 45º Elbow)
F - Support Ring & Plate PSPXT-8
G - Firestop FS-8
H - Roof Flashing PRF-7 (1/12 - 7/12 pt�)
PRF-12 (7/12 - 12/12 pt�)
I - Heat Shield RHS103
J - Heat Guard MTKOG
Connection and installation of the vent components should
adhere to the following guidelines:
Section 3-3-2: Venting Components
The following components and associated Montigo part num-
bers are available for installation of a Wall Mounted Termination�
Use only Montigo Vent Components� Use of non-Montigo parts
will void the warranty and may impede operation of the fireplace.
IMPORTANT:
Please Refer to your Building Envelope Engineer
or Waterproofing Consultant for a review of ALL
penetrations through exterior walls or the roof�
 Montigo recommends the use of a flex section for the final pipe
connected directly to the fireplace offering greater flexibility of
installation and absorption of movement.
 Firestops must be installed as required by National & local codes .
 Montigo recommends that all exterior corners and joints be sealed
with exterior caulking. However, we encourage you to consult
your Building Envelope Engineer or Waterproofing Consultant
for further recommendations.
 Use any combination of rigid and flex pipe as required and in
any orientation (Male connectors can face in any direction).
 Flex sections may be stretched up to 50% of their total length
(e.g. a 24” section maybe stretched to 36”).
 Connect all vent sections using a minimum of three sheet metal
screws on the outer pipe flue.
 Ensure the pipe ends male to female slide in a minimum of 1
1/2” of overlap.
 Ensure all horizontal runs are supported with a minimum of 3
supports per 10’ of venting.
 When hanging/ supporting venting, ensure that 1” clearance
is maintained on sides and bottom of vent runs and 2” above
horizontal vent runs to any combustible material.
 Rigid pipe may be cut less than half way from the female end only�
 Ensure when cutting sections of rigid pipe to maintain integrity
of internal supports.
 Place the springs, supplied with the pipe kit, between the outer
and inner pipes to keep the pipes separate and avoid any
possible hot spots.