Meinberg SHSPZF LANTIME - Manual (Page 104)

SNMP branch Variable Data type Description
mbgLtCfgNotify mbgLtCfgNotifyNTPNotSync string(combination ) Exactly one, none or a combination of
the following notification types:
email=sending an email
wmail=sending a winpopup-message
snmp=sending a SNMP-trap,
disp=showing on wall mount display,
syslog=sending a syslog-entry
for the event „NTP not synchronized“
mbgLtCfgNotifyNTPStopped string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „NTP Daemon stopped“
mbgLtCfgNotifyServerBoot string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „Timeserver reboot“
mbgLtCfgNotifyRefclockNotR
esponding
string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „Refclock not ready“
mbgLtCfgNotifyRefclockNotSy
nc
string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „Refclock not synchron“
mbgLtCfgNotifyAntennaFaulty string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „GPS antenna not connected or
dammaged“
mbgLtCfgNotifyAntennaRecon
nect
string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „GPS antenna reconnected“
mbgLtCfgNotifyConfigChange
d
string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „Configuration changed“
mbgLtCfgNotifyLeapSecondAn
nounced
string (combination) (see mbgLtCfgNotifyNTPNotSync) for
the event „Leap second announced“
mbgLtCfgEthernet mbgLtCfgEthernetIf0IPv4IP string (IPv4 IP-
address)
IPv4-address of first network interface
of the timeserver
mbgLtCfgEthernetIf0IPv4Netm
ask
string (IPv4
Netzmaske)
IPv4-netmask of first network interface
of the timeserver
mbgLtCfgEthernetIf0IPv4Gate
way
string (IPv4 IP-
address)
IPv4-address of the default gateway of
the timeservers first network interface
mbgLtCfgEthernetIf0DHCPCli
ent
integer (0 =
disabled, 1 =
enabled)
Configure the first network interface of
the timeserver with DHCP?
mbgLtCfgEthernetIf0IPv6IP1 string (IPv6 IP-
address)
First IPv6-IP-address of the timeservers
first network interface
mbgLtCfgEthernetIf0IPv6IP2 string (IPv6 IP-
address)
Second IPv6-IP-address of the
timeservers first network interface
mbgLtCfgEthernetIf0IPv6IP3 string (IPv6 IP-
address)
Third IPv6-IP-address of the timeservers
first network interface
mbgLtCfgEthernetIf0IPv6Auto
conf
integer (0 =
disabled, 1 =
enabled)
Activate autoconf for the IPv6 -
configuration of the timeservers first
network interface?
mbgLtCfgEthernetIf0NetlinkM
ode
integer (0..4) Configuration of the network-speed and
duplex settings of the timeservers first
network interface
0 = autosensing,
1 = 10Mbit/s half duplex,
2= 10Mbit/s full duplex,
3=100Mbit/s half duplex,
4=100Mbit/s full duplex
For all additional Ethernet interfaces of the timeserver, “If0“ only has to be replaced
with “Ifx“, where “x“ is substituted by the number of the desired Ethernet interface.
Example: The IPv4-address of the timeservers third Ethernet interface can be set with
mbgLtCfgEthernetIf2IPv4IP!
104