Marantz PS-17 - Manual (Page 39)

29
ENGLISH
Example 2
Turn the main amplifier ON fi Change the amplifier’s input source to
LD fi Set the Surround mode to DOLBY fi Switch the TV to video
input fi Set the laser disc player to PLAY
1. Use a ballpoint pen or other sharp point to press the MACRO
button x.
2. Press the LD Function button ,.
• Here the LD Function button , is used as the macro button,
but any function button can in fact be used.
3. To set the various steps of the macro, press the following buttons
in order:
POWER ON c, LD ,, AMP * ,, 2 (DOLBY) ⁄7, TV * ,,
VIDEO (use Jog Dial n to select VIDEO and press ENT button
m) , LD * ,, 3 ⁄0.
4. When you are finished programming the macro, use a ballpoint
pen or other sharp point to press the
MACRO button x. The
remote controller returns to normal mode.
Now, execute the macro you just programmed.
1. Press the LD Function button , for 3 seconds.
The macro commands are transmitted in order, and the names of
the operations being performed are displayed on LCD a in
order.
• When executing this macro, function operations AMP*, TV*,
and LD* only switch the command set of the remote controller
and no signal is transmitted to the component.
• To cancel the transmission of a programmed macro, use the
Cursor buttons ⁄0 to press 7.
CLEARING MACRO PROGRAMS
The following procedure is used to erase macros you have
programmed into the remote controller’s memory.
1. Press and hold the CLEAR button ⁄5, then the button for the
function , to be cleared (in this case LD) for 3 seconds. LDCL?
will appear on LCD a. If you wish to continue the clearing
operation, press the
OK Cursor button ⁄0.
• To cancel the memory clearing operation, do not press OK
Cursor button ⁄0 and simply touch any other button.
EXAMPLES OF MACRO PROGRAMS
Example 1
Change the input source for the amplifier to CD and play the 3rd track
on a CD in the CD player.
1. Use a ballpoint pen or other sharp point to press the MACRO
button x, then press the CD Function button ,. CD-M is
displayed on the LCD.
2. Press CD ,, 3 ⁄7, and 3 ⁄0 buttons.
When you are finished programming the macro, use a ballpoint
pen or other sharp point to press the
MACRO button x.
Now, execute the macro you just programmed.
1. Press the CD Function button , for 3 seconds.
2. The macro commands are transmitted to the components in
order, and the names of the operations being performed are
displayed on the LCD in order.
ON OFF ON / OFF
SOURCE
MACRO MODE
LEARNING REMOTE
CONTROL RC-17PS
POWER
MEMO GUIDE MUTE
ENT ENT
CH VOL
1 2 4 5
6 7 8 0 9
DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
CLEAR
3
C D
OK
ON OFF ON / OFF
SOURCE
MACRO MODE
LEARNING REMOTE
CONTROL RC-17PS
POWER
MEMO GUIDE MUTE
1 2 3 4 5
DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
AMP
2
L D
CLEAR
C D
ON OFF ON / OFF
SOURCE
MACRO MODE
LEARNING REMOTE
CONTROL RC-17PS
POWER
MEMO CLEAR GUIDE MUTE
1 2 3 4 5
6 7 8 0 9
C D DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
MEMO GUIDE MUTE
1 2 3 4 5
6 7 8 0 9
C D DVD CD-R/MD
DSS T V VCR
TUNER TAPE
PHONO
AUTO SRS 6.1 5ch-ST.
Dolby H P-DIRE. 2CH OSD SLEEP
AMP
2
L D
CLEAR