Basic operation, 24 english, Learn mode – Marantz PS-17 User Manual
Page 34: Use mode, Source
![background image](https://www.manualsdir.com/files/796102/content/doc034.png)
24
ENGLISH
LEARN MODE
The remote controller is capable of learning and memorizing the
remote control codes used by almost any other remote controller you
may already own.
• If no commands have been programmed for a particular function
button, the remote controller will transmit whatever codes have
been factory preset.
• The following example shows how to program your remote
controller and how to use the codes for a laser disc player (LD).
• The remote controller infrared receiver is located at the top of the
remotecontroller.
1.
Use a ballpoint pen or other sharp point to press the
MODE
button
z until the
LEARN
indicator is displayed. Each time you
press this button, the mode will cycle through
LEARN
fi
NAME
fi
USE
.
Stop when the
LEARN
indicator starts to blink.
2.
Place the laser disc’s remote controller so that its infrared signal
transmitter is facing the infrared signal receiver on the Marantz
remote controller at a distance of about 5 centimeters (2 inches).
3.
Press the
LD Function
button ,.
4.
Press the
PLAY
button
⁄0 (3
OK
). The
LEARN
indicator
changes from blinking to continuously lit.
5.
Press and hold the
PLAY
button on the laser disc player’s remote
controller. The remote controller has finished learning the
command when
OK
appears on the LCD a.
• If
AGAIN
appears on the LCD, some error has prevented the
command from being learned. If this happens, simply repeat
the procedure from step 4.
• In the rare event that
NG
appears on the LCD, it means that
the remote controller you are attempting to learn from uses
special signals that cannot be learned by the Marantz remote
controller.
6.
Follow the same procedure to make the remote controller learn
the ten-key
⁄7 operation used by the laser disc player’s remote
controller.
BASIC OPERATION
USE MODE
The remote controller will normally be used in the USE mode.
It comes preset with codes commonly used to control 11 types of
components manufactured by Marantz and Philips, including DSS,
DVD, TV, LD, VCR, TUNER, CD, TAPE, CD-R/MD, and AMP, as well
as many others that utilize the RC-5 remote control language.
1.
Press once one of the
Function
buttons
, to change to another
component’s commands, such as LD button.
2.
LD
will be displayed on the LCD and the function codes will be
set to operate the laser disc player, and if you double clicked the
LD function button, the preamplifier input will be changed as well.
3.
Now you can operate the laser disc player. When a button is
pressed, the
symbol indicates that a remote code is being
transmitted.
is not displayed if a button for which no code
has been set is pressed.
4.
The
Jog Dial
n is used to select any one of up to 10 direct
operations that can be performed for each of the 11 functions
(LD, TV, AMP, etc.). Rotate the
Jog Dial
n to select one of these
commands. The number of the current page is indicated by
-
.
Page numbers cycle up or down, for example
fi
fi
fi
fi etc. or fi
fi
fi
fi etc. depending on which
way the
Jog Dial
n is rotated then press
OK
⁄0 button.
The last page position for any given command function is
retained in the memory even if the remote controller is switched to
the command function for another component. (Last Memory)
If it is left for approximately 1 minute without pressing any
buttons, all items on the LCD will go off except the function
indicator.
Even if the display goes off, the remote controller will hold the
page position and other data. The display may be activated
again by pressing any button.
MEMO
CLEAR
GUIDE
MUTE
1
2
3
4
5
6
7
8
0
9
DSS
T V
VCR
TUNER
TAPE
PHONO
AUTO
SRS
6.1
5ch-ST.
Dolby H
P-DIRE.
2CH
OSD
SLEEP
AMP
2
L D
ENT
ENT
CH
VOL
ON
OFF
ON
/OFF
S
OURCE
MA
CRO
MO
DE
LEARNING REMOTE
CONTROL
RC-17PS
POWER
OK
MEMO
CLEAR
GUIDE
MUTE
1
2
3
4
5
6
7
8
0
9
DSS
T V
VCR
TUNER
TAPE
PHONO
AUTO
SRS
6.1
5ch-ST.
Dolby H
P-DIRE.
2CH
OSD
SLEEP
AMP
2
L D
CH
VOL
C D
DVD
CD-R/MD
OK