26 english, Erasing programmed codes, Rewriting names – Marantz PS-17 User Manual
Page 36
26
ENGLISH
7.
Follow the same procedure to enter “D-A”. When finished, press
the
OK
Cursor button
⁄0. Pressing
OK
permanently fixes the
newly written characters.
• Up to 5 alphanumeric characters may be entered in the
Command Name indicator of the LCD.
• To rewrite the names of the other items in the Command
Name indicator, use the
Jog Dial
n to select the desired
command and repeat from step 5.
8.
When you are finished rewriting, use a ballpoint pen or other
sharp point to press the
MODE
button
z to return the remote
controller to the USE mode. The
USE
indicator is displayed on
the LCD, and the newly programmed codes now can be used.
ERASING PROGRAMMED CODES
(Returning to Factory Presets)
Codes that have been programmed into the memory can be erased in
3 ways: by button(s), by function(s), and by Jog Dial command.
1.
Use a ballpoint pen or other sharp point to press the
MODE
button
z to switch the remote controller to the LEARN mode, so
that the
LEARN
indicator is blinking on the LCD.
Note:
Erasing of programmed codes is only possible in the LEARN
mode.
2.
Erasing by Button(s)
To erase the codes and names programmed for any button,
press and hold the
CLEAR
button
⁄5, then press the button to be
erased twice. This will return the button to its factory presets or
leave it empty if no factory presets are available.
Jog Dial codes may be erased in the same way, by pressing and
holding the
CLEAR
button
⁄5 while using the
Jog Dial
n to call
up the command to be erased, then pressing one of the
ENT
buttons
m on either side of the
Jog Dial
n twice. This will return
the button to its factory presets or leave it empty if no factory
presets are available.
To erase codes programmed for the
CLEAR
button
⁄5, simply
press the
CLEAR
button
⁄5 continuously for 3 seconds.
As an example, let’s clear the PLAY command from the laser disc
player command set.
REWRITING NAMES
This remote controller allows the names accessible by
Jog Dial
control
n to be rewritten with new ones of your choosing.
• Rewriting of names is performed for each individual function.
• Let’s use a laser disc player as an example to show how to change
the
’s “SIDE-A” to “LD-A”.
1.
Use a ballpoint pen or other sharp point to press the
MODE
button
z to switch the remote controller to the NAME mode. The
NAME
indicator blinks.
2.
Press the
LD Function
button
,.
3.
Use the
Jog Dial
n to select the page for which you wish to enter
a new name.
4.
The character on the left-hand side of the Command Name
indicator on LCD b will flash, indicating that it is the character
ready to be rewritten. New characters entered will be written over
the top of the current character so that the current character is
erased.
Use the
<
and
>
Cursor buttons
⁄0 to select the characters to be
rewritten.
5.
Use the ten-key pad
⁄7 to select the desired alphanumeric
characters.
Pressing the number buttons on the ten-key pad will cycle
through the alphanumeric characters as follows:
Ten keypad
Press, press again, press again, etc.
1
A
fi
B
fi
C
fi
1
fi
A
2
D
fi
E
fi
F
fi
2
fi
D
3
G
fi
H
fi
I
fi
3
fi
G
4
J
fi
K
fi
L
fi
4
fi
J
5
M
fi
N
fi
O
fi
5
fi
M
6
P
fi
Q
fi
R
fi
6
fi
P
7
S
fi
T
fi
U
fi
7
fi
S
8
V
fi
W
fi
X
fi
8
fi
V
9
Y
fi
Z
fi
/
fi
9
fi
Y
0
SPACE fi
+
fi
—
fi
,
fi
’
fi
0
fi
SPACE
( )
6.
Therefore, to enter the letter “
L
”, press the 4-key on the ten-key
pad
⁄7 3 times in a row to cycle from J to K to L.
Once the desired character “
L
” appears, press either of the
<
and
>
Cursor buttons
⁄0 and the L will be permanently written
over the former character. Press the 0-key in order to replace
unneeded extra characters with spaces.
MEMO
CLEAR
GUIDE
MUTE
1
2
3
4
5
6
7
8
0
9
DSS
T V
VCR
TUNER
TAPE
PHONO
AUTO
SRS
6.1
5ch-ST.
Dolby H
P-DIRE.
2CH
OSD
SLEEP
AMP
2
L D
ON
OFF
ON / OFF
SOURCE
MACRO
MODE
LEARNING REMOTE
CONTROL RC-17PS
POWER
MEMO
GUIDE
MUTE
CH
VOL
1
2
3
4
5
C D
DVD
CD-R/MD
DSS
T V
VCR
TUNER
TAPE
PHONO
AUTO
SRS
6.1
5ch-ST.
AMP
OK
2
L D
CLEAR
ENT
ENT