Harken 7807 2-Point Lift - 60 lb - Manual

3-Easy
Steps 3
Store
2
Lift
Includes
all mounting
hardware
1
Secure
Plan Location of 2-Point Lift System
Read instructions before starting. Plan ceiling location of mounting
board. Position welded screw eye (E) at top of adjoining wall.
Distance from organizer (B) on end of board to welded screw
eye must be equal or greater than lifting distance. See Fig. 2
and “Install Welded Screw Eye” instructions next page.
Mount Board to Ceiling
Draw a centerline the length of a 6' (1.83 m) 2" x 6" pine mounting
board. Use a stud finder to locate ceiling trusses/rafters on which
to mount system (follow manufacturer’s instructions). Drill four
(three minimum)
5 /
16
" (8 mm) evenly-spaced clearance holes on
board centerline matching truss/rafter locations. Use holes in
mounting board as template to mark ceiling. Drill truss/rafters
using a
7 /
32
" (5.5 mm) drill bit. Install board using 5 /
16
" x 4" (8 x
100 mm) lag bolts (K) with flat washers (L). Do not over-tighten. Printed in USA 4977 04/15
Harken, Inc. • 1251 E. Wisconsin Ave. • Pewaukee, WI 53072 USA • Tel: 262-691-3320 • Fax: 262-691-3008 • Email: [email protected] • Web: www.hoister.com
Maximize garage
space by storing
items up and out of the
way. This block-and-tackle system
allows one person to easily raise and
lower items with a single rope. A self-
locking pulley grips instantly even if
the rope is accidentally released.
Tools/supplies needed (purchase separately): Electric/hand drill; drill bits: 3 /
32
" (2.5 mm), 7 /
32
" (6 mm); Stud finder;
stepladder; safety glasses, tape measure; one (1) 2" x 6" x 6' (50 mm x 152 mm x 1.83 m) grade 2 or better pine board.
#7807 maximum load:
60 lb (27 kg)
SAVE TIME! READ THE ENTIRE MANUAL BEFORE BEGINNING HOISTER INSTALLATION.
IMPORTANT SAFETY INFORMATION
• DO NOT UNTIE ANY ROPES
System comes ready to install. Leave F, G, and H together.
• DO NOT RAISE OR LOWER HOISTER
with anyone standing under object.
• SECURELY ANCHOR
each fastener to a truss/rafter.
EASY TO USE
EASY TO INSTALL
COMPLETE KIT
SELF-LOCKING
STORE AT CEILING LEVEL
One person can easily raise and lower
with a single control rope.
Three styles store
everything from
canoes, kayaks,
and SUPs to bikes,
ladders and roof
racks.
(45, 60, 90, 145, 200 lb)
WE STORE IT ALL!
ONE-PERSON OPERATION
Raises and lowers easily
with a single control rope.
EASY TO INSTALL
Kit comes complete.
SAFE, SELF-LOCKING
Safety cleat grips instantly if
rope is accidentally released.
LIFTS EVENLY
From 10 to 200 lb.
Web: www.hoister.com
MAXIMIZE GARAGE SPACE
WARNING: Do not screw into laminated rafters.
They are not intended to accept fasteners.
Consult rafter maker for recommendations.
Screwing into laminated rafters can weaken
system, causing load to fall which can cause
an accident.
WARNING: Do not over-tighten pigtail lag screws
past top thread. This can weaken fastener hold
which can weaken system, causing load to fall
which can cause an accident.
225A
Max Max Lifting weight
Part
No. Description
Mechanical
advantage
ceiling height item width Min Max
ft m ft m lb kg lb kg
7800 1-Point storage system bike/utility lift 2:1 10 3.05 — — 10 4.5 45 20
7801 4-Point storage system 3:1 10 3.05 5 1.52 15 7 60 27
7802 4-Point storage system 4:1 10 3.05 5 1.52 25 11 90 41
7803 4-Point storage system 6:1 10 3.05 5 1.52 45 20 145 66
7806 4-Point storage system 8:1 10 3.05 5 1.52 75 34 200 91
7807 2-Point storage system 3:1 10 3.05 5 1.52 15 7 60 27
7808 4-Point SUP storage system 2:1 10 3.05 5 1.52 10 4.5 45 20
WARNING! Strictly follow all instructions to avoid an accident,
damage to property, personal injury, or death. See www.harken.
com/manuals for additional safety information.
WARNING! Do not use this product for human suspension.
Components can fail causing person to fall, possibly resulting
in serious injury or death.
KIT INCLUDES
A 2 Harken micro pulleys
B 1 Harken organizer
C 2 #10 x 2 1 /
2
" (6 x 63 mm) screws
D 1 shackle
E 1 welded screw eye
F 1 Harken block and tackle
G 2 black drop ropes: 1 long, 1 short
H 1 single hoisting rope
I 2 webbing straps with buckles 7' (2.13 m)
J 2 pigtail lag screws
K 4 lag bolts 5 / 16 " x 4" (8 x 100 mm)
L 4 washers
PURCHASE SEPARATELY IF NEEDED
1 pine board (riser) (grade 2)
2" x 6" x 7" (50 mm x 152 mm
x 180 mm). Do not use for rafters
running sideways.
TOOLS
Electric/hand drill Safety glasses
Drill bits: 5 /
32
" (4 mm)
7 /
32
" (5.5 mm)
5 /
16
" (8 mm)
Pencil
Stud finder
Stepladder
Tape measure
224 Harken
micro pulleys
A 237 Harken
organizer
B
HFS961
#10 x 2 1 /
2
" (6 mm x 63 mm) screws
C
HCP1452 28'
drop ropes
G
7754A.Assy
Harken block
and tackle
F
HCP1443
welded
screw eye
E
072 Harken
shackle
D
HCP1483 35'
single hoisting rope
H
HCP1660.SET
webbing straps with buckles
7' (2.13 m)
I
HFS987
washers
L
HFS988
lag bolts 5 /
16
" x 4"
(8 x 100 mm)
K
HCP1444
pigtail lag screws
J
Harken, Inc. • N15W24983 Bluemound Rd, Pewaukee, WI 53072-4974 • Tel: 262-691-3320 • Fax: 262-701-5780• Email: [email protected] • Web: www.hoister.com