Harken 62 Handhold - Manual (Page 2)

Cutout Size
4 7 /
16
" X 1 3 /
4
"
(113 mm X 44 mm)
Printed in USA. 4402 11/13
Harken equipment requires minimal maintenance, but some is required to give the best service and to comply with
Harken's limited warranty. It is important to keep equipment clean by frequent flushing with fresh water.
For additional safety, maintenance and warranty information see www.harken.com/manuals or the Harken ® catalog.
Maintenance
Warranty
Install Handhold
1. Cut out template and use to draw a pattern for cutting opening.
2. Use handhold to mark hole position.
3. For self-tapping sheet metal or wood screws, drill 5 holes using 1/8", 9/63" or 3.5mm drill.
For machine screws, drill 5 holes using 3/16" or 5 mm holes.
4. Apply high quality marine sealant around outer rim of handhold and inside screw holes.
5. Secure handhold by tightening screws or nuts.
Cutout Size
4 7 /
16
" X 1 3 /
4
"
(113 mm X 44 mm)
Harken equipment requires minimal maintenance, but some is required to give the best service and to comply with
Harken's limited warranty. It is important to keep equipment clean by frequent flushing with fresh water.
For additional safety, maintenance and warranty information see www.harken.com/manuals or the Harken ® catalog.
Maintenance
Warranty
Install Handhold
1. Cut out template and use to draw a pattern for cutting opening.
2. Use handhold to mark hole position.
3. For self-tapping sheet metal or wood screws, drill 5 holes using 1/8", 9/63" or 3.5mm drill.
For machine screws, drill 5 holes using 3/16" or 5 mm holes.
4. Apply high quality marine sealant around outer rim of handhold and inside screw holes.
5. Secure handhold by tightening screws or nuts.
Cutout Size
4 7 /
16
" X 1 3 /
4
"
(113 mm X 44 mm)
Harken equipment requires minimal maintenance, but some is required to give the best service and to comply with
Harken's limited warranty. It is important to keep equipment clean by frequent flushing with fresh water.
For additional safety, maintenance and warranty information see www.harken.com/manuals or the Harken ® catalog.
Maintenance
Warranty
Install Handhold
1. Cut out template and use to draw a pattern for cutting opening.
2. Use handhold to mark hole position.
3. For self-tapping sheet metal or wood screws, drill 5 holes using 1/8", 9/63" or 3.5mm drill.
For machine screws, drill 5 holes using 3/16" or 5 mm holes.
4. Apply high quality marine sealant around outer rim of handhold and inside screw holes.
5. Secure handhold by tightening screws or nuts.
Cutout Size
4 7 /
16
" X 1 3 /
4
"
(113 mm X 44 mm)
Harken equipment requires minimal maintenance, but some is required to give the best service and to comply with
Harken's limited warranty. It is important to keep equipment clean by frequent flushing with fresh water.
For additional safety, maintenance and warranty information see www.harken.com/manuals or the Harken ® catalog.
Maintenance
Warranty
Install Handhold
1. Cut out template and use to draw a pattern for cutting opening.
2. Use handhold to mark hole position.
3. For self-tapping sheet metal or wood screws, drill 5 holes using 1/8", 9/63" or 3.5mm drill.
For machine screws, drill 5 holes using 3/16" or 5 mm holes.
4. Apply high quality marine sealant around outer rim of handhold and inside screw holes.
5. Secure handhold by tightening screws or nuts.
Printed in USA. 4402/08-12
Printed in USA. 4402 11/13
Printed in USA. 4402 11/13