Harken 724 Big Boat deck organizer - Manual (Page 2)

Tighten bolts only wrist tight (10 ft-lb/14 N-m) to remove play between
block and deck. Do not use power drivers. Overtightening will permanently
damage organizer and cause sheaves to bind.
Tighten wrist tight (10 ft-lb/14 N-m) Do not use power drivers.
DO NOT OVERTIGHTEN—ORGANIZERS/FOOTBLOCKS!
CORRECT INCORRECT
Printed in USA. 4947 01/14
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Maintenance
Warranty
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets and
screws. This is not serious and may be removed with a fine abrasive.
Flush blocks thoroughly with fresh water. Periodically, disassemble the blocks and clean
with detergent and fresh water. Lubrication is not required.
Clear plastic washers should always be used between stainless fasteners and aluminum
sideplates. Stainless fasteners which pass through aluminum blocks should be coated
with an antiseize compound.
Locking nuts should not be used after being removed three times. When replacing
shackles and fasteners, use Harken parts to maintain the proper strength.
IMPORTANT! Exposure to some teak cleaners and other caustic solutions can
result in discoloration of part and is not covered under the Harken warranty.
Tighten bolts only wrist tight (10 ft-lb/14 N-m) to remove play between
block and deck. Do not use power drivers. Overtightening will permanently
damage organizer and cause sheaves to bind.
Tighten wrist tight (10 ft-lb/14 N-m) Do not use power drivers.
DO NOT OVERTIGHTEN—ORGANIZERS/FOOTBLOCKS!
CORRECT INCORRECT
Printed in USA. 4947 01/14
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Maintenance
Warranty
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets and
screws. This is not serious and may be removed with a fine abrasive.
Flush blocks thoroughly with fresh water. Periodically, disassemble the blocks and clean
with detergent and fresh water. Lubrication is not required.
Clear plastic washers should always be used between stainless fasteners and aluminum
sideplates. Stainless fasteners which pass through aluminum blocks should be coated
with an antiseize compound.
Locking nuts should not be used after being removed three times. When replacing
shackles and fasteners, use Harken parts to maintain the proper strength.
IMPORTANT! Exposure to some teak cleaners and other caustic solutions can
result in discoloration of part and is not covered under the Harken warranty.
Tighten bolts only wrist tight (10 ft-lb/14 N-m) to remove play between
block and deck. Do not use power drivers. Overtightening will permanently
damage organizer and cause sheaves to bind.
Tighten wrist tight (10 ft-lb/14 N-m) Do not use power drivers.
DO NOT OVERTIGHTEN—ORGANIZERS/FOOTBLOCKS!
CORRECT INCORRECT
Printed in USA. 4947 01/14
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Maintenance
Warranty
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets and
screws. This is not serious and may be removed with a fine abrasive.
Flush blocks thoroughly with fresh water. Periodically, disassemble the blocks and clean
with detergent and fresh water. Lubrication is not required.
Clear plastic washers should always be used between stainless fasteners and aluminum
sideplates. Stainless fasteners which pass through aluminum blocks should be coated
with an antiseize compound.
Locking nuts should not be used after being removed three times. When replacing
shackles and fasteners, use Harken parts to maintain the proper strength.
IMPORTANT! Exposure to some teak cleaners and other caustic solutions can
result in discoloration of part and is not covered under the Harken warranty.
Tighten bolts only wrist tight (10 ft-lb/14 N-m) to remove play between
block and deck. Do not use power drivers. Overtightening will permanently
damage organizer and cause sheaves to bind.
Tighten wrist tight (10 ft-lb/14 N-m) Do not use power drivers.
DO NOT OVERTIGHTEN—ORGANIZERS/FOOTBLOCKS!
CORRECT INCORRECT
Printed in USA. 4947 01/14
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Maintenance
Warranty
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets and
screws. This is not serious and may be removed with a fine abrasive.
Flush blocks thoroughly with fresh water. Periodically, disassemble the blocks and clean
with detergent and fresh water. Lubrication is not required.
Clear plastic washers should always be used between stainless fasteners and aluminum
sideplates. Stainless fasteners which pass through aluminum blocks should be coated
with an antiseize compound.
Locking nuts should not be used after being removed three times. When replacing
shackles and fasteners, use Harken parts to maintain the proper strength.
IMPORTANT! Exposure to some teak cleaners and other caustic solutions can
result in discoloration of part and is not covered under the Harken warranty.