Harken 438 Cam adapter plate - Manual (Page 2)

Printed in USA 4853 12/13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequently flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets
and screws. This is not serious and may be removed with a fine abrasive.
With the exception of winches, do not use grease unless specifically recommended in
the instruction sheets.
Important! Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
Maintenance
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Warranty
4. Using plate as a guide,
drill and tap through spar.
5. Screw cam to spar with two screws (apply Loctite ® to threads).
Loctite ® is a trademark of Henkel AG & Company KGaA
6. Do not over tighten. Cam should be quite secure, but pawls should snap
closed smartly.
CAUTION Three fasteners must secure cam cleat and adapter
to spar. Using only center fastener will result in cam suddenly
coming off mast and causing damage or injury.
CORRECT
INCORRECT
Printed in USA 4853 12/13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequently flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets
and screws. This is not serious and may be removed with a fine abrasive.
With the exception of winches, do not use grease unless specifically recommended in
the instruction sheets.
Important! Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
Maintenance
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Warranty
4. Using plate as a guide,
drill and tap through spar.
5. Screw cam to spar with two screws (apply Loctite ® to threads).
Loctite ® is a trademark of Henkel AG & Company KGaA
6. Do not over tighten. Cam should be quite secure, but pawls should snap
closed smartly.
CAUTION Three fasteners must secure cam cleat and adapter
to spar. Using only center fastener will result in cam suddenly
coming off mast and causing damage or injury.
CORRECT
INCORRECT
Printed in USA 4853 12/13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequently flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets
and screws. This is not serious and may be removed with a fine abrasive.
With the exception of winches, do not use grease unless specifically recommended in
the instruction sheets.
Important! Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
Maintenance
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Warranty
4. Using plate as a guide,
drill and tap through spar.
5. Screw cam to spar with two screws (apply Loctite ® to threads).
Loctite ® is a trademark of Henkel AG & Company KGaA
6. Do not over tighten. Cam should be quite secure, but pawls should snap
closed smartly.
CAUTION Three fasteners must secure cam cleat and adapter
to spar. Using only center fastener will result in cam suddenly
coming off mast and causing damage or injury.
CORRECT
INCORRECT
Printed in USA 4853 12/13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequently flushing with fresh water. In
corrosive atmospheres, stainless parts may show discoloration around holes, rivets
and screws. This is not serious and may be removed with a fine abrasive.
With the exception of winches, do not use grease unless specifically recommended in
the instruction sheets.
Important! Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
Maintenance
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken ® catalog.
Warranty
4. Using plate as a guide,
drill and tap through spar.
5. Screw cam to spar with two screws (apply Loctite ® to threads).
Loctite ® is a trademark of Henkel AG & Company KGaA
6. Do not over tighten. Cam should be quite secure, but pawls should snap
closed smartly.
CAUTION Three fasteners must secure cam cleat and adapter
to spar. Using only center fastener will result in cam suddenly
coming off mast and causing damage or injury.
CORRECT
INCORRECT