Harken 302 Line/Wire Through-Deck Block - Manual (Page 2)

Drilling/Cut-Out Templates
Printed in USA 4406 09-13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In corrosive
atmospheres, stainless parts may show discoloration around holes, rivets and screws.
This is not serious and may be removed with a fine abrasive.
For additional safety, maintenance and warranty information see
www.harken.com/manuals or the Harken
®
catalog.
Maintenance
Warranty
17 /
32
"
(13.5 mm)
306
2 15 /
16
" (74.5 mm)
2 5 /
16
" (58.5mm)
9 /
16
"
(14.5 mm)
310
2 15 /
16
" (74.5 mm)
3 11 /
16
" (93.5mm)
Drilling/Cut-Out Templates
Printed in USA 4406 09-13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In corrosive
atmospheres, stainless parts may show discoloration around holes, rivets and screws.
This is not serious and may be removed with a fine abrasive.
For additional safety, maintenance and warranty information see
www.harken.com/manuals or the Harken
®
catalog.
Maintenance
Warranty
17 /
32
"
(13.5 mm)
306
2 15 /
16
" (74.5 mm)
2 5 /
16
" (58.5mm)
9 /
16
"
(14.5 mm)
310
2 15 /
16
" (74.5 mm)
3 11 /
16
" (93.5mm)
Drilling/Cut-Out Templates
Printed in USA 4406 09-13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In corrosive
atmospheres, stainless parts may show discoloration around holes, rivets and screws.
This is not serious and may be removed with a fine abrasive.
For additional safety, maintenance and warranty information see
www.harken.com/manuals or the Harken
®
catalog.
Maintenance
Warranty
17 /
32
"
(13.5 mm)
306
2 15 /
16
" (74.5 mm)
2 5 /
16
" (58.5mm)
9 /
16
"
(14.5 mm)
310
2 15 /
16
" (74.5 mm)
3 11 /
16
" (93.5mm)
Drilling/Cut-Out Templates
Printed in USA 4406 09-13
Harken equipment requires minimal maintenance, but some is required to give the best
service and to comply with Harken's limited warranty.
It is important to keep equipment clean by frequent flushing with fresh water. In corrosive
atmospheres, stainless parts may show discoloration around holes, rivets and screws.
This is not serious and may be removed with a fine abrasive.
For additional safety, maintenance and warranty information see
www.harken.com/manuals or the Harken
®
catalog.
Maintenance
Warranty
17 /
32
"
(13.5 mm)
306
2 15 /
16
" (74.5 mm)
2 5 /
16
" (58.5mm)
9 /
16
"
(14.5 mm)
310
2 15 /
16
" (74.5 mm)
3 11 /
16
" (93.5mm)