2 handling, 3 lifting – Flowserve CPXV fitted with WW User Manual
Page 10
CPXV - WW/CW USER INSTRUCTIONS ENGLISH 85392698 10-09
Page 10 of 36
flowserve.com
Typical sound pressure level L
pA
at 1 m reference 20
µ
Pa, dBA
3 550 r/min
2 900 r/min
1 750 r/min
1 450 r/min
Motor size
and speed
kW (hp)
Pump
only
Pump and
motor
Pump
only
Pump and
motor
Pump
only
Pump and
motor
Pump
only
Pump and
motor
<0.55(<0.75)
72
72
64
65
62
64
62
64
0.75 (1)
72
72
64
66
62
64
62
64
1.1 (1.5)
74
74
66
67
64
64
62
63
1.5 (2)
74
74
66
71
64
64
62
63
2.2 (3)
75
76
68
72
65
66
63
64
3 (4)
75
76
70
73
65
66
63
64
4 (5)
75
76
71
73
65
66
63
64
5.5 (7.5)
76
77
72
75
66
67
64
65
7.5 (10)
76
77
72
75
66
67
64
65
11(15)
80
81
76
78
70
71
68
69
15 (20)
80
81
76
78
70
71
68
69
18.5 (25)
81
81
77
78
71
71
69
71
22 (30)
81
81
77
79
71
71
69
71
30 (40)
83
83
79
81
73
73
71
73
37 (50)
83
83
79
81
73
73
71
73
45 (60)
86
86
82
84
76
76
74
76
55 (75)
86
86
82
84
76
76
74
76
75 (100)
87
87
83
85
77
77
75
77
90 (120)
87
88
83
85
77
78
75
78
110 (150)
89
90
85
87
79
80
77
80
150 (200)
89
90
85
87
79
80
77
80
200 (270)
1
1
1
1
85
87
83
85
300 (400)
–
87
90
85
86
1
The noise level of machines in this range will most likely be of values which require noise exposure control, but typical values are inappropriate.
Note: for 1 180 and 960 r/min reduce 1 450 r/min values by 2 dBA. For 880 and 720 r/min reduce 1 450 r/min values by 3 dBA.
Each product has a unique serial number. Check
that this number corresponds with that advised and
always quote this number in correspondence as well
as when ordering spare parts or further accessories.
2.2 Handling
Boxes, crates, pallets or cartons may be unloaded
using fork lift vehicles or slings dependent on their size
and construction.
2.3 Lifting
To avoid distortion, the pump unit
should be lifted as shown.
Pumps with drivers over approximately 7.5 kW, are
supplied with the pump packed as a separate item
from the driver. These and should be lifted
separately into their installed position, using lifting
points on the pump soleplate, and on the motor.
When lifting pumps with drivers fitted,
the resulting center of gravity may be above the lifting
points, and the method of slinging must prevent the
machine tipping during the lift.
Slings, ropes and other lifting gear must be positioned
where they cannot slip and where a balanced lift is
obtained.
For improved stability unbolt the driver and lift the
driver and pump separately.
For lifting the driver refer to the
dimension drawing of the driver.
Lift points for the pump or the pump
and the driver.