Fieldpiece SC76 - Temperature and Capacitance Clamp Meter - Manual (Page 2)

SPECIFICATIONS
Display: LCD with a maximum read-
ing of 3400.
Analog bar graph: 34 segments with
measurements 20 times per sec-
ond.
Data Hold: Operating on all ranges
Range(RNG): Operating on all autor-
anges
Overrange: "OL" mark indication.
Auto power off: Approx. 10 minutes.
Measurement rate: 2 times per sec-
ond, nominal.
Operating environment: 32 to 122°F
(0 to 50°C) at <70% R.H.
Storage temperature: -4 to 140°F
(-20 to 60°C), 0 to 80% R.H. with
battery removed.
Accuracy: Specifications good in
ambient conditions of 73°F ±9°F
(23°C ±5°) , <75% relative humidity.
Temperature Coefficient: 0.1 ×(speci-
fied accuracy) per °F/°C; 32 to 64°F
(0 to 19°C); 82 to 122 °F
(28 to 50°C).
Altitude: 6561.7 Feet (2000m).
Jaw opening capability: 38mm con-
ductor.
Power: Single standard 9-volt battery,
NEDA 1604, JIS 006P, IEC 6F22.
Battery life: 300 hours typical with
alkaline.
Accessories: One pair test leads,
one pair of small alligator clips, k-
type thermocouple, 9V battery
(installed), and operating instruc-
tions.
Safety: UL, CE, Cat III 600V, IEC
61010-1 (EN61010-1) and
IEC61010-2-032 (EN61010-2-032).
DC volts
Ranges: 340mV, 3400mV, 34V, 340V,
600V
Resolution: 0.1mV
Accuracy: ±(0.5% rdg + 1 dgt)
Input impedance: 3M
Ω on V inputs,
10M Ω on mV input
Overload protection: 600VDC or AC
rms
Normal mode rejection ratio: >50dB
@ >49Hz
Common mode rejection ratio:
>120dB up to 1000VDC
Transient protection: 6kV for 10μ
sec
AC volts(50Hz - 500Hz)
Ranges: 3.4V, 34V, 340V, 600V
Resolution: 1mV
Accuracy: ±(2.0% rdg + 4 dgts) 50 ~
500Hz
Input impedance: 3M Ω
Overload protection: 600V DC or AC
rms
Transient protection: 6kV for 10μ
sec
AC current(50Hz - 60Hz)
Ranges: 34A, 300A
Resolution: 0.01A
DC Accuracy:
±(3.0% rdg + 5 dgts) 0 ~ 300A / 50
~ 60Hz
Overload protection: 300AAC
DC current
Ranges: 340μA, 3400μA
Resolution: 0.1μA
Accuracy: ±(1.0% rdg + 1 dgt)
Voltage burden: 1V, (8V on 3400μA
range)
Overload protection: 500VDC or AC
rms
Resistance
Ranges: 340 Ω, 3.4kΩ, 34kΩ, 340kΩ,
3.4M Ω, 34MΩ
Resolution: 100m Ω
Accuracy:
±(1.2% rdg + 4 dgts) on 340 Ω to
340k Ω ranges
±(1.5% rdg + 4 dgts) on 3.4M Ω
range
±(3.0% rdg + 5 dgts) on 34M
Ω
range
Open circuit volts: -0.45VDC typical,
(-1.2VDC on 340 Ω range)
Overload protection: 500VDC or AC
rms
Temperature
Range: -30 to 1000°F (-35 to 600°C)
Resolution: 0.1°
Accuracy: ±1°F (32 to 120°F); ±0.5°C
(0 to 49°C),
±1% + 1.5°F (-4 to 750°F); ±1% +
1°C (-20 to 400°C),
±2% + 4°F (-30 to -4°F, 750 to
1000°F);
±2% +2°C (-35 to -20, 400 to
540°C)
Sensor type: K-type thermocouple
Overload protection: 60 VDC or 30
VAC rms
Diode test
Test current: Approx. 1.0mA
Resolution: 1mV
Accuracy: ±(2% rdg + 3 dgts)
Open circuit volts: 3.0Vdc typical
Audible indication: Less than 0.2V
Overload protection: 500VDC or AC
rms
Continuity
Audible indication: Less than 300 Ω
Response time: 500ms
Green LED will be on continuously.
Capacitance
Range: 340μF
Resolution: 0.1μF
Accuracy: ±(3% rdg + 5 dgts)
Test frequency: 16Hz
Test voltage: <3.0V
Overload protection: 500VDC or AC
rms
Hi-V(voltage) warning
>30VAC/DC meter beeps, red LED
blinks.
Non-contact voltage
Senses voltage 24V to 600V AC
beeper chirps and big bright red LED
comes on, works when meter dial is on
any range.
Voltage
Resistance
DC Current (μADC)
Temperature
AC Current
Selecting ranges
For DC voltage, set the meter to the
VDC parameter instead of VAC as
shown above.
For all ranges and functions choose
a range just above the value you
expect. If display reads "OL" (over-
load), select a higher range. If display
shows less than three numbers, select
a lower range for better resolution.
Capacitance
CE
This instrument complies with the
requirements of the following
European Community Directives:
89/336/EEC (Electromagnetic
Compatibility) and 73/23/EEC (Low
Voltage) as amended by 93/68/EEC
(CE Marking).
Service
Return any defective SC76 to
Fieldpiece for warranty service along
with proof of purchase. Contact
Fieldpiece for out of warranty repair
charges.
www.fieldpiece.com
Insure the
temperature
being measured
is stable.
Maintain good
contact between
the thermocouple
and what's being
measured.
Disconnect test leads from
voltage before plugging
thermocouple in.