Selecting ranges, Voltage v = ir, Functional specifications – Fieldpiece SC66 - Basic Manual Ranging Clamp Meter User Manual

Page 2: General specifications, Dc current <200µadc, Limited warranty, Obtaining service

selecting ranges

For DC voltage, set the meter to

the VDC parameter instead of VAC

as shown above.

For all ranges and functions

choose a range just above the value

you expect. If display reads “OL”

(overload), select a higher range.

If display shows less than three

numbers, select a lower range for

better resolution.

Voltage

V = ir

volts = current x resistance

Capacitance

resistance

aC Current

temperature

Notes to chart on left:

(1)

50-60Hz

(2)

Input impedance is 560Kohms on

volts ranges, 10Mohm on millivolts

ranges. All ranges will withstand

600VAC/600VDC.

(3)

50Hz-500Hz.

(4)

Protected by PTC (positive tem-

perature coefficient) resistor. If an

overload occurs on microamps DC,

disconnect from circuit for 30 sec-

onds so the PTC can reset.

(5)

Accuracy 1

F (32

F to 120

F);

1%+1.5

F (-4

F to 750

F);

2%+4

F (-30

F to -4

F, 750

F to

1000

F); all withstand 30V max.

(6)

Test frequency 34Hz at <3.5V. Will

withstand up to 500V.

(7)

Turns on >30V.

(8)

Senses 24VAC to 600VAC.

(9)

0.3VDC typical open circuit voltage.

(3V on 200ohm range). Withstands

up to 500V on any ohms range.

(10)

Turns on <100 ohms within 100mS.

Will withstand up to 500V.

(11)

Holds highest reading.

www.fieldpiece.com

Functional specifications

Accuracy specifications @ 74°F±8°F, relative humidity less than 75%. Accuracy

specified as ±% of reading ± number of least significant digits.

limited warranty

This meter is warranted against

defects in material or workmanship

for one years from date of purchase.

Fieldpiece will replace or repair the

defective unit, at its option, subject to

verification of the defect.

This warranty does not apply to

defects resulting from abuse, neglect,

accident, unauthorized repair,

alteration, or unreasonable use of the

instrument.

Any implied warranties arising

from the sale of a Fieldpiece product,

including but not limited to implied

warranties of merchantability and

fitness for a particular purpose, are

limited to the above. Fieldpiece

shall not be liable for loss of use of

the instrument or other incidental or

consequential damages, expenses,

or economic loss, or for any claim of

such damage, expenses, or economic

loss.

State laws vary. The above limitations

or exclusions may not apply to you.

Obtaining service

Call Fieldpiece Instruments for

one-price-fix-all warranty service

pricing. Send check or money order

for the amount quoted. Send the

meter freight prepaid to Fieldpiece

Instruments. Send proof of date

and location of purchase for in-

warranty service. The meter will be

repaired or replaced, at the option of

Fieldpiece, and returned via least cost

transportation.

General specifications

Indicators: Low battery. Overrange:

“OL” is displayed.

Environmental: Operating tempera-

ture 32°F to 122°F, storage 0°F

to 140°F with batteries removed,

RH<80%.

Measurement rate: 2.5 times/sec

nominal.

Battery: 9V NEDA 1604; 150 hours

typical with carbon zinc (installed).

Auto power off: Meter automati-

cally turns off after approximately

1 hour.

Temperature coefficient: 0.1 X

(specified accuracy) per °F above

82°F and below 64°F.

Industry specifications: IEC/

EN61010-1, IEC/EN61010-2-32,

Cat III (600V for SC66 and SC67)

class 2 and pollution degree 2, in

accordance with IEC-664 indoor

use. UL listed to UL3111. C-Tick

certified.

This instrument complies with

the requirements of the following

European Community Directives:

89/336/EEC (Electromagnetic

Compatibility) and 73/23/EEC (Low

Voltage) as amended by 93/68/EEC

(CE Marking).

Insure the

temperature being

measured is stable.

Maintain good

contact between

the thermocouple

and what’s being

measured.

Disconnect test leads from voltage

before plugging thermocouple in.

DC Current <200µaDC

A PTC resistor, not a fuse, protects

your clamp meter. When an overload

occurs on µADC, do not apply current

for at least 30 seconds to reset the PTC.

CAPACITOR

DISCHARGE

v37

Function Range

Accuracy

/resolution

SC66

SC67

AAC

200

3%+5 / 0.1 (1)

3%+5 / 0.01

VAC(2,3)

200

1.2%+3 / 0.1

600

2%+5 / 1

VDC(2)

0.5%+1 / 0.01

200

0.5%+1 / 0.1

µADC(4)

200

1%+1 / 0.1

°F (5)

200°F

1°F / 0.1

1000°F 1%+1.5°F / 1

MFD (6)

200

3%+5 / 0.1

Hi-V (7)

Beep

& LED

NCV (8)

Ohms(9)

200

1%+3 / 0.1

200k

1%+3 / 0.1k

Continuity

(10)

MAX hold

(11)

Diode test

×
×

Beep

&LED

Beep

&LED

+24V