beautypg.com

Dakota Digital 3X User Manual

Page 24

background image

MAN 650067:G

24

Fuel sensor setup (

SENDER

)

This menu is used to select the fuel level sensor type. The table, on previous page,

shows the seven options and resistance ranges as well as the custom option.
Note: You need to calibrate the custom sensor to your specific fuel sensor if you are
using this option in the custom setup in the steps below.

When “

sender

” is displayed, press and hold SW1 until you get “

-

Release SW1 and the current sensor selection will be displayed.

Press and release SW1 to scroll through the sensor options “

GM 30

” “

GM 90

” “

GM 250

F 10

” “

F 150

” “

V 180

” “

SW 33

” “

CUSTOM

” “

BUS

When the desired setting is displayed, press and hold SW1 until “ - ” “

DONE

” is displayed.

Release the switch to go onto the next menu item.

Custom fuel sender curve setup (

CUSTOM

)

You will need to have the sender out of the tank, or begin with the tank empty and
add fuel during the custom fuel sender setup.
*** The factory default custom curve is 110 empty and 5 ohms full

When “

CUSTOM

CUSTOM

CUSTOM

CUSTOM

” is displayed, press and hold SW1 until you get “

-

Release SW1 and the speed display will show the current sender resistance as read by the

control box.

The message display will show “

SET 00

SET 00

SET 00

SET 00

”. Move the float to the empty position and then

press and release the SW1.

The message display will show “

SET 33

SET 33

SET 33

SET 33

”. Move the float to 1/3 full and then press and

release the SW1.

The message display will show “

SET 66

SET 66

SET 66

SET 66

”. Move the float to 2/3 full and then press and

release the SW1.

The message display will show “

SET 99

SET 99

SET 99

SET 99

”. Move the float to the full position and then press

and release the SW1. The new sender is now stored under the “

CUSTOM

CUSTOM

CUSTOM

CUSTOM

” sender selection.

The message display will be back in the fuel sub-menu showing “

test

test

test

test

”.

***If the resistances recorded during custom calibration are not in sequence you will get
a “

FAIL

FAIL

FAIL

FAIL

” message at the end of calibration. No values will be saved and calibration must

be started again. Make sure the resistance of the sensor is linear from empty to full.

Note: Once the custom sender is programmed, go back and ensure that “

CUSTOM

CUSTOM

CUSTOM

CUSTOM

” is

selected in the “

SENDER

SENDER

SENDER

SENDER””””

menu. Programming the custom sender curve does not

automatically make it the ‘active’ sender.

Fuel sensor test (

TEST

)

This menu will allow you to check the resistance the control box is reading from the fuel

level sensor. This can be used as a diagnostic tool if you are having trouble or feel that the
reading is incorrect. You can use the table of fuel sensors above to get an idea of the
resistance you should be seeing.

When “

TEST

” is displayed, press and hold SW1 until you get “

-

”.

Release SW1 and the current resistance from the fuel level sensor will be displayed on the

speedometer and “

R fuel

” is displayed on the odometer readout.

Press and release SW1 to scroll through the next sensor input if you wish “

R TEMP

” “

V OIL

R FUEL

”.

Once complete, hold SW1 until “

-

” “

DONE

” is displayed.

Release the switch to go onto the next sub-menu item.

Note: Fuel level sensors are generally not precise; in the test function you should expect to see
some error. For instance a GM 0-90 sensor may display 5 ohms empty and 97 ohms full. If you
are within 10% of the values in the table, this is considered within specification.