Daktronics Outdoor LED Scoreboards Installation - Manual (Page 52)

REV
01
DATE:
8 JAN 14
ADDED ALLOWABLE TENSION AND SHEAR CAPACITY DETAILS
ADDED NON-BKLT AD PANEL MOUNTING DETAILS
CHANGED DWG TO B SIZED.
BY:
JAVA
DAKTRONICS, INC. THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON
THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY.
DO NOT REPRODUCE BY ANY MEANS WITHOUT THE
EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC.
COPYRIGHT 2014 DAKTRONICS, INC.
BROOKINGS, SD 57006
DO NOT SCALE DRAWING
PROJ: OUTDOOR SCOREBOARD
TITLE: I-BEAM CLAMP MOUNTING, SHEET METAL ATTACHMENT
DESIGN: KSCHNABEL DRAWN: KSCHNABEL DATE: 06-JAN-14
SCALE: 1/8
SHEET: REV JOB NO: FUNC-TYPE-SIZE 1129110
1 OF 1 01 P 1753 E - 10 - B
MOUNTING INSTRUCTIONS:
1. LIFT THE FIRST SECTION OF THE DISPLAY INTO POSITION
AGAINST I-BEAMS.
NOTE: IF THE DISPLAY IS MADE UP OF MULTIPLE SECTIONS
ALWAYS INSTALL THE BOTTOM SECTION FIRST AND WORK UP.
2. STARTING ON THE TOP OF THE SECTION BEING INSTALLED
MARK AND DRILL 9/16" HOLES IN THE CENTER OF THE TOP
FLANGE OF THE SECTION. MAKE SURE THE HOLES ARE
POSITIONED AS CLOSE TO THE I-BEAM FLANGES AS POSSIBLE.
3. INSTALL ALL THE HARDWARE SHOWN PROVIDED AND TIGHTEN
THE SECTION IN THE DESIRED LOCATION.
4. ONCE THE TOP OF THE SECTION IS SECURE MOVE TO THE
BOTTOM OF THE SECTION AND REPEAT THE STEPS ABOVE.
5. IF THE DISPLAY IS MADE OF MULTIPLE SECTIONS REPEAT
THE ENTIRE PROCEDURE ABOVE.
6. ENSURE ALL 1/2" HARDWARE IS TORQUED TO THE SPECIFIED
AMOUNT.
STANDARD SHEETMETAL SCOREBOARD/BACKLIT
AD PANEL MOUNTING METHOD
ALLOWABLE CAPACITY PER EACH CLAMP:
SHEAR = 160 LBS
TENSION = 1700 LBS
SHEAR AND TENSION LOAD
DIRECTION ARE AS INDICATED ON
ROTATED VIEWS
STANDARD NON-BACKLIT AD PANEL MOUNTING METHOD
QUALIFIED FOR SECTIONS UP TO 5' IN HEIGHT
USING RECOMMENDED STRUCTURE
FRONT ROTATED VIEW
1/2-13 SQUARE NUT
WASHER PLATE @2
MOUNTING CHANNEL
1/2" SPLIT LOCK WASHER
1/2" FLAT WASHER
I-BEAM CLAMP
#12-14 X 1.500" SELF DRILLING SCREW
1/2-13 X 3.500 BOLT
TENSION
SHEAR-X
SHEAR-Y
FRONT OF SECTION
SECTIONS
VERTICAL BEAM - RECOMMENDED FLANGE THICKNESS 3/16" - 3/4"
IF I-BEAM FLANGE IS GREATER THAN 3/4" THICK LONGER BOLTS
WILL BE REQUIRED AT THE CUSTOMER'S EXPENSE.
1/2-13 X 3.500 BOLT - BOLT THREAD MUST ENGAGE ENTIRE DEPTH
OF SQUARE NUT. BOLT MUST BE TIGHTENED TO 40FT-LB TORQUE
1/2" SPLIT LOCK WASHER
1/2" FLAT WASHER
I-BEAM CLAMP - ASSURE CLAMP IS TIGHTLY ENGAGED
TO I-BEAM AND NUT
1/2-13 SQUARE NUT
1/8" THICK WASHER PLATE @2 - IT IS CRITICAL 2 WASHER
PLATES ARE USED PER HARDWARE ASSEMBLY
MOUNTING CHANNEL WITH OBROUND SLOTS - CENTER THE
CHANNEL 0N THE I-BEAM AS MUCH AS POSSIBLE
#12-14 X 1.500" SELF DRILLING SCREW - INSERT SCREW UNTIL
HEAD CONTACTS BEAM CLAMP. DO NOT STRIP OUT SCREW.
TOP VIEW
1/2-13 SQUARE NUT
WASHER PLATE @2
MOUNTING CHANNEL
1/2" SPLIT LOCK WASHER
1/2" FLAT WASHER
I-BEAM CLAMP
#12-14 X 1.500" SELF DRILLING SCREW
1/2-13 X 3.500 BOLT
TENSION
SHEAR-X
SHEAR-Y
REAR ROTATED VIEW
VERTICAL BEAM - RECOMMENDED FLANGE THICKNESS 3/16" - 3/4"
IF I-BEAM FLANGE IS GREATER THAN 3/4" THICK LONGER BOLTS
WILL BE REQUIRED AT THE CUSTOMER'S EXPENSE.
1/2-13 X 3.500 BOLT - BOLT THREAD MUST ENGAGE ENTIRE DEPTH
OF SQUARE NUT. BOLT MUST BE TIGHTENED TO 40FT-LB TORQUE
1/2" SPLIT LOCK WASHER
1/2" FLAT WASHER
I-BEAM CLAMP - ASSURE CLAMP IS TIGHTLY ENGAGED
TO I-BEAM AND NUT
1/2-13 SQUARE NUT
1/8" THICK WASHER PLATE @2 - IT IS CRITICAL 2 WASHER
PLATES ARE USED PER HARDWARE ASSEMBLY
MOUNTING CHANNEL WITH OBROUND SLOTS - CENTER THE
CHANNEL 0N THE I-BEAM AS MUCH AS POSSIBLE
#12-14 X 1.500" SELF DRILLING SCREW - INSERT SCREW UNTIL
HEAD CONTACTS BEAM CLAMP. DO NOT STRIP OUT SCREW.
TOP VIEW
FRONT OF SECTION
SECTIONS