TVLogic LUM-300W - Manual (Page 6)

10 4K LCD Monitor 4K LCD Monitor 11
FRONT
3. Controls & Functions
●
[MENU] Button
- Used to activate the OSD menu.
●
[DOWN/BRIGHT] Button
- Used to move up through the menus during
the OSD menu activation and also to decrease
the value of the selected feature.
- May also be used to control the BRIGHT value
during the OSD menu inactivation. Use the
UP/DOWN buttons to adjust the value.
●
[UP/CONTRAST] Button
- Used to move down through the menus
during the OSD menu activation and also to
increase the value of the selected feature.
- It may also be used to control the CONTRAST
value during the OSD menu inactivation. Use
the UP/DOWN buttons to adjust the value.
●
[ENTER/VOLUME] Button
- Used to confirm a chosen value (or mode).
- May also be used to control the VOLUME
value during the OSD menu inactivation. Use
the UP/DOWN buttons to adjust the value.
●
[OPERATE] Lamp
- Indicates condition and power status of unit.
- Light turns off when the power is
disconnected.
- Standby mode is indicated by a red LED light.
- Normal (active) mode is indicated by a Green
LED light.
- Restores to previous status when monitor
power turns off and comes back on.
●
[POWER] Button
- Used to turn the power on and off.
5). H/V DELAY
- Used to check horizontal and vertical
sync simultaneously by moving the screen
up/down/left/right.
- In this mode, the brightness of image
automatically increase for easy verification
of synchronized signals.
6). FREEZE
- Captures still frame on-screen.
7). VIDEO RANGE
- Used to select the range of brightness.
* LIMITED(EX) : Output : 16 ~ 255
* FULL : Output : 0 ~ 255
* LIMITED : Output : 16 ~ 235
* EXTENTION : Input : 16 ~ 235 Output : 0
~255
8). DITHERING
- Used to activate/deactivate the 10bit
dithering function.
9). COLOR TEMP
- Used to controls the color temperature
and allows instant access to preset
the color temperature settings.
10). HD DISPLAY
- Used to control the display ratio in HD
mode.
- Available values are 16:9, 1.85:1 and 2.35:1.
11). AUDIO LVM
- Used to activate/deactivate the Audio Level
Meter.
3. Controls & Functions
REAR
●
[REMOTE] (RJ-45)
- Provides connection to control equipment
for external monitor control.
- Features can be changed in the GPI section
of OSD menu.
●
[RS422 IN/OUT] (RJ-45)
- Used to control the monitor with a protocol
provided by TVLogic.
●
[DP-A,B]
- Signal input terminal for Display Port signal.
●
[HDMI-A,B,C,D]
- Signal input terminal for HDMI A,B,C,D
signal.
●
[SDI-A,B,C,D] (BNC)
- HD/SD SDI signal input terminal for SDI
A,B,C,D signal.
●
[Audio out] (PHONE JACK)
- Select the left/right Audio disembedded
signal output.
●
[Ethernet & USB]
- Ethernet and USB port for easy updates on
new functions and color calibration.
- Used to control the monitor with a protocol
provided by TVLogic.
●
~ AC IN
- 100 ~ 240V AC 50/60Hz
●
DC IN
- 24V
When using the product make sure to ground,
whenever possible, before connecting the
input signal cable in order to prevent any
possible damage to the product or connected
devices. The damage may include signal noise,
malfunction of main board or display panel.
And the connected devices such as camera or
video source player may also be influenced
through signal cable. Please check if the AC
power source and the power extender or
power distributor is grounded.