TVLogic LUM-300W - Manual (Page 13)

24 4K LCD Monitor 4K LCD Monitor 25
LUM-300W SDI A
●
USER CONFIG SET
- Used to save and apply in three kinds of user
configurations.
- Available modes are USER1, USER2 and
USER3.
- Assignable items for each USER1, USER2 and
USER3 settings are the [MARKER] menu of
MARKER, CENTER MARKER, SAFETY AREA,
MARKER MAT and MARKER COLOR, the
[PICTURE] menu of BRIGHT, CONTRAST,
CHROMA, PHASE and APERTURE.
●
LOCK NUMBER
- This function is not supported.
●
LOCK ENABLE
- This function is not supported.
●
OSD DISPLAY
- Used to control the OSD display time.
- Available values are 3 SEC, MAIN MENU 20
SEC, MAIN MENU CONTINUE, MAIN MENU 3,
4 SEC, 20 SEC and CONTINUE.
●
OSD POSITION
- Used to control the OSD position.
- The OSD position displays on the bottom left
position of quad screen.
- Available positions are Center, Right-
Top(R-T), Bottom-Right(R-B), Top-Left(L-T)
and Bottom-Left(L-B).
●
INTERNAL PATTERN
- Generates White Pattern internally.
- Selectable range is from 0% to 100% with 5%
increment.
●
SET DEFAULT
- Used to initialize OSD values to factory
default.
●
BATTERY CHECK
- Used to activate/deactivate the battery
output voltage check function.
[9] SYSTEM
5. Menu Operations
PAGE I >> PAGE II
USER CONFIG SET
LOCK NUMBER
LOCK ENABLE
OSD DISPLAY
OSD POSITION
INTERNAL PATTERN
SET DEFAULT
BATTERY CHECK
USER 1
yyyyyyyy
--------
CONTINUE
R-T
OFF
ON
1080/60i
[9] SYSTEM
5. Menu Operations
●
S/W UPGRADE
- Used to upgrade the firmware using the USB
memory (Thumb drive).
- Set the S/W UPGRADE as [ON] to start the
USB memory search.
- When the USB memory is detected, the S/W
UPGRADE START menu becomes activated.
- It takes approximately 10 sec for upgrading
CPU.
- While updating ‘FPGA A’, ‘F1’ button on the
monitor will flicker. (20 to 25 min)
- While updating ‘FPGA B’, ‘F2’ button on the
monitor will flicker. (15 to 20 min)
- While updating ‘VXP’, ‘F3’ button on the
monitor will flicker. (15 to 20 min)
* In order to reduce the time of firmware
update, we recommend that you upgrade
what you need. According to putting the file
on the USB, you can update CPU, FPGA A, B, or
VXP partially.
●
S/W UPGRADE START
- Select the S/W UPGRADE START menu to
start the firmware upgrade.
- Do not turn off the monitor while the
Upgrade is conducting.
●
FAN CONTROL
- Used to activate/deactivate the cooling fan
of the monitor.
- Set the FAN CONTROL as [ON]. The cooling
fan operates automatically when the internal
temperature of the monitor is higher than
set temperature.
PAGE II >> PAGE I
S/W UPGRADE
S/W UPGRADE START
FAN CONTROL
OFF
OFF
LUM-300W SDI A 1080/60i
PAGE II >> PAGE I
BOARD VERSION 0001 0101 0.01 5
MAIN : UD MODE
BRIG. : 0
CONT. : 0
COLOR : 6500K
SCAN : OVER
ALM : OFF
VOLT. : 23.6V
LUM-300W SDI A 1080/60i
KEYPAD VERSION
MCU VERSION
FPGA VERSION
GPU VERSION
●
MAIN
- Indicates the current display mode.
●
BRIG.
- Displays set value of BRIGHT.
●
CONT.
- Displays set value of CONTRAST.
●
COLOR
- Displays set value of color temperature.
●
SCAN
- Displays set value of scan mode.
●
ALM
- Displays set value of Audio Level Meter.
●
VOLT.
- Displays the current power supply voltage