Woodhaven 1440-1441: Digital Readout Kit for EZ Lift User Manual
Please read carefully
BEFORE BEGINNING
Identify and verify that you have all the parts
listed. Read thru the instructions at least once,
familiarizing yourself with the parts and process before
proceeding. You'll need a #3 Phillips screwdriver.
WHAT GLIDE DOES YOUR 1435-1437 HAVE?
If you purchased your 1435-1437 EZ Lift before 10/1/10,
you'll need to attach a new Glide (1440A - in 1441 Parts List)
in place of the existing Glide. See fig. 1 & 2. If you purchased
your 1435-1437 EZ Lift after 10/1/10, move on to the next
section of the instructions (back of page) and disregard this
section as you already have the 1440A Glide on your EZ Lift.
IF YOU PURCHASED THE 1435-1437 BEFORE 10/1/10
Start by clamping the two Ultra Tracks together. Remove the
existing Glide, opposite the motor tightening bolt, by loosening
(not removing) the screws enough to slide it off both Ultra
Tracks. Make sure you remove the correct Glide! See fig. 1.
Remove the existing hardware, one screw at a time, from
old Glide and loosely attach this hardware to the new Glide
(1440A) in the same locations & exactly the same way. Make
sure the smooth side of the tighteners are facing the Glide when
you attach them. Slide the new Glide into place on the two
Ultra Tracks, then tighten the three screws with oval nuts (on
the short Ultra Track) as you apply pressure against the edge
of the Glide where shown. Remove the clamp. See fig. 2.
Snug the two remaining screws to adjust the tension on the
tighteners. Do not overtighten or you may strip the tighteners. Then
loosen the screws approximately 1/8th turn and test how well the
EZ Lift moves by using the crank. Tighten or loosen the screws to
adjust the tension on the tighteners according to your preference.
YOU CAN NOW MOVE ON TO THE NEXT
SECTION ON THE BACK OF THIS PAGE.
1440 & 1441
Digital Readout
Please Read Carefully!
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1440 Parts List:
Part Description
Quantity
1445
Digital Readout unit . . . . . . . . . . . . . . . . . . . 1
1440D
Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5765B
Offset Oval Nut . . . . . . . . . . . . . . . . . . . . . . . 2
5775B
5/8" screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
WN002
nylon washer . . . . . . . . . . . . . . . . . . . . . . . . . 2
5770B
1/2" screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1440C
Display Mount . . . . . . . . . . . . . . . . . . . . . . . . 1
HB020
1/4-20 x 3/4" bolt . . . . . . . . . . . . . . . . . . . . . 2
5521
Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1441 Parts List:
Includes all the parts above, plus the part below.
1440A
Glide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Apply pressure to Glide here
as you tighten three screws.
After clamping the two tracks
together, remove this Glide.
Motor tightening
bolts is on this side.
2
1