Dynex DX-L37-10A - Manual (Page 10)

Making connections
7
The remote control may not work if direct sunlight or bright light shines
on the remote sensor. Either move your TV or change the angle at
which you use the remote control.
Programming a universal remote control
to work with your TV
You can operate your TV with a new or existing universal remote
control.
To program a universal remote control:
1 Find the code for your universal remote control by identifying its
model (or your set-top box’s remote control manufacturer and
model) on the charts below, then make note of the numbered
code below it. You will use the numbered code to program your
remote control to work with your TV.
Codes for other remote controls are available online at:
www.dynexproducts.com\t-customer_support.aspx
Tips:
• The brand name is often visible on the front of the universal remote
control, and the model number is often visible on the back.
• If your universal remote control isn’t listed on the chart, refer to your
universal remote control’s instructions and try codes for the brands
Orion, Emerson, Memorex, Sansui, Sylvania, or Zenith. You may need
to try several codes before fi nding a match.
2 Follow your universal remote control’s instructions to enter the
code you found in Step 1.
Tips:
• If your universal remote control has a code search feature, run a code
search to identify a code that matches your TV. See your universal
remote control’s instructions for details.
• If your universal remote control has a “Learn” feature, you can
manually program it using your TV remote to “teach” the commands
one at a time. See your universal remote control’s instructions for
details.
3 If all else fails, you must use a different universal remote control
that can operate both your set-top box and your TV. Five such
remotes are listed on the chart, but many other compatible
models are available in the market.
For more help, call technical support for your universal remote
control or set-top box manufacturer, or call the Dynex Customer
Care Center at 1-800-305-2204.
Making connections
Cautions:
Check the terminals for position and type before making any connections.
Loose connections can result in image or color problems. Make sure that
all connections are tight and secure.
The external audio/video equipment shown in these illustrations may be
different from your equipment. If you have questions, refer to the user
manual that came with your equipment.
Always turn the power off when connecting external equipment.
Connecting the power
To connect the power:
• Connect the power cord (included) to the AC IN jack on the back
of your TV.
Notes:
This illustration is for reference only. The AC plug may be different on your
TV.
Your TV should only be operated from the power source indicated on the
label.
Always unplug the AC power cord from the AC power outlet when you will
not be using your TV for an extended period of time.
Connecting an antenna, cable TV, or
satellite TV box
To connect an antenna, cable TV, or satellite TV box:
1 Connect one end of a 75 ohm cable (not included) to the RF OUT
jack on the antenna or on the cable or satellite TV box.
2 Connect the other end of the cable to the RF jack on the back of
your TV.
Notes:
Use a 75 ohm cable to eliminate interference and noise from radio waves.
Do not bundle the 75 ohm cable with the power cord or other cables.
If the antenna is not installed correctly, contact qualified service personnel
to correct the problem.
Dynex TV codes for universal remote controls
(for all Dynex TVs manufactured after Jan. 1, 2007)
Universal remote control manufacturer and model
Philips
PHDVD5,
PH5DSS,
PMDVR8,
PDVR8 DirectTV
RC23 RCA
RCU807 One for All
URC-6690 Sony
RM-VL600
115 10463 135 0464 8043
Set-top box manufacturer and model
Comcast
M1057 Dish
Network
VIP508,
VIP622 Motorola
DRC800 TIVO
Series 3, HD
0463 720 0463 0091
Antenna, cable TV, or
satellite RF jack
RF jack
Back of TV
RF coaxial cable (75 ohm)
DX-L37-L42-10A_08-1837.book Page 7 Wednesday, January 21, 2009 1:17 PM