Dynex DX-32L152A11 - Manual

COMP
AV VIDEO L R
Y P b Pr
L
R ANT/CABLE IN DIGITAL AUDIO OUT
AV VIDEO L R
COMP
AV VIDEO L R
Y P b Pr
L
R ANT/CABLE IN DIGITAL AUDIO OUT
HDMI2 HDMI 1
PC/DVI AUDIO IN VGA
32" LCD TV
QUICK SETUP GUIDE
DX-32L152A11
Remote control
and
2 AAA batteries
TV stand and screws
Quick Setup Guide
INPUT
ENTER
EN-31203B
HDMI
AUDIO PICTURE
MENU
CH VOL MUTE
VIDEO COMP VGA
ZOOM
EXIT
TV
1 2 3
6 5 4
7 8 9
0 RECALL
GUIDE
INFO
MTS/SAP CCD TIME SLEEP
HDMI cable
(not included) HDMI device
Back of TV
N
Video device
Composite audio/video
cable (not included)
Back of TV
Antenna cable
Component video device
Back of TV
Component video cable
Composite
cable
WE ARE GOING GREEN!
A copy of the manual is not provided in the box
but is avalaible at www.dynexproducts.com
DIGITAL AUDIO
OUT
Home theater
system
Digital coaxial cable
Back of TV
Front and side features
Installing the stand
1 Remove the stand from the box and place it on a table or bench.
2 Lay the TV on a flat, cushioned surface.
3 Align the base with the bottom of the TV, then secure the base to the TV
with the three screws provided.
Installing a wall-mount bracket
1 Carefully place your TV screen face-down on a cushioned, clean surface to
protect the screen from damages and scratches.
2 Remove the pedestal stand. See “Removing the stand” in your User Guide.
3 Secure the wall-mount bracket to the back of your TV using the four screws
provided with the bracket.
Connecting a DVD or Blu-ray DVD player, cable
box, satellite receiver, or game station
Using HDMI (best)
Using component (better)
Note: Cable connectors and jacks are often color-coded. Match the colors
when you connect the component video and AV cables.
Using composite (good)
Note: Cable connectors and jacks are often color-coded. Match the colors
when you connect the composite AV cable.
Connecting an antenna
Connect a 75 ohm cable (not included) to the ANT/CABLE IN jack on the back
of your TV and the RF OUT jack on the antenna.
Connecting a home theater system
Using digital audio:
Note: The DIGITAL OUTPUT jack only works with digital TV channels.
Connecting power
Connect the power cable to a power outlet.
Setting up your remote control
1 While pressing the release button on the battery compartment cover on
the back of the remote, lift the cover off the remote.
2 Insert two AAA batteries into the battery compartment. Make sure that the
+ and – symbols on the batteries align with the + and – symbols in the
battery compartment.
3 Replace the cover. Make sure that the lock snaps into place.
To program your existing remote control to work with your Dynex TV, see the
table below for common codes. If you have problems programming your
remote, or need a different remote control code, visit
www.dynexproducts.com for the latest remote control code information.
For step-by-step instructions on programming the remote control, see your
User Guide.
Philips
PHDVD5, PH5DSS,
PMDVR8, PDVR8
115
DirectTV
RC23
10463
RCA
RCU807
135
One for All
URC-6690
0464
Sony
RM-VL600
8043
Comcast
M1057
0463
Dish Network
VIP508, VIP622
720
Motorola
DRC800
0463
TIVO
Series 3, HD
0091
Universal remote control makers and models Set-top box makers and models
Universal remote control TV codes (for all Dynex TVs manufactured after Jan. 1, 2007)
Power
indicator
Remote control
sensor