Tie Down Jet Rail XL - Manual (Page 4)

TIE DOWN ENGINEERING 4 www.tiedown.com
4. Attach Front Deck Mount to Frame Tube
Attach front deck mount to front of frame tube (front of tube has a
single hole on each side of the tube,Picture 6). Front deck mount is
mounted flush against end of the frame tube using the U-bolt, metal
washers and nyloc nuts as shown in Picture 5.
Parts required for this step.
# Stk. # Description Qty.
4 26608 Front Deck Mount 1
1 26617 Jet Rail Frame Tube 1
26 84472Z 1/2” U-Bolt 1
33 10645 1/2” Nyloc Nut 2
37 10573 1/2” Flat Washers 2
4A. Attach Brace to Front Mount
Mount using 3 - 3/8”x1” carriage bolts or 3/8”x1” hex head bolts.
Brace must be positioned so that it is level with the bottom of the front
brace. As shown in picture 5
Parts required for this step.
# Stk. # Description Qty.
4a 26618 Front brace 1
39 10804 Carriage bolt 3
34 10627 3/8” Nyloc nut 3
NOTE: At this time, place frame tube/carriage with deck mounts
attached, in the general area where you are planning to attach the Jet
Rail to your dock. Make sure there is room for the watercraft to be
winched onto the Jet Rail without obstructions.
5. Attach Winch Mount Extension Tube to Winch Mount Tube.
Slide Extension Tube into front of Jet Rail Frame Tube. Cut-out in front
deck mount matches the end that slides into the tube. Bolt winch
mount tube to extension tube using the 3- 3/8” x 4” Grade 5 hex head
bolts and nyloc nuts (Picture 7a).
Parts required for this step.
# Stk. # Description Qty.
1 26617 Jet Rail Frame Tube 1
6 26610 Winch Mount Ext. Tube 1
9 26613 Winch Mount Tube 1
28 BBB3750400 3/8” x 4” Hex Head Bolts 3
34 10627 3/8” Nyloc Nut 3
5a. Assemble Rollers to Jet Rail Deck
Insert a 6-3/4” x 1/2” roller shaft, and two 1/2” pal nuts, place the
5-1/2” long plastic bushings with three nylon bushings (Picture 7b).
(NOTE: some hardware kits substitute a 1/2”x6-1/2” hex head bolt
& nut for the roller shaft.)
6. Attach Jet Rail Deck To Carriage Assembly
Lift Jet Rail deck assembly over carriage. Align carriage tube hole with
pivot hole in deck. (Picture 8) Install 1/2” x 7” bolt with 1/2” nyloc nut.
(Front of deck has two holes on each side) End with rollers goes to the
rear/water side.
Parts required for this step.
# Stk. # Description Qty.
5 26614 Jet Rail Deck Assembly 1
2 26606 Jet Rail Carriage Assembly 1
31 10936 1/2” x 7 “ Hex Bolt 1
33 10645 1/2” Nyloc Nut 1
1
33/nut
26
37/washer
4
4a
Picture 5
9- Winch Mount Tube
6-Winch Mount Ext. Tube
Picture 8
Picture 7a
5
31
32
36
35
21
17
3
15
21
27
34
33
19
35
36
35
19
14
Markings on Grade 5
Hex Head Bolts
Picture 6
Picture 7b