beautypg.com

Custom programming options, Throttle profile selection, M2 dig software flow chart – Novak Brushed Speed Control: M2 Dig Field Guide (55-1846P-1 Rev. 1.1) User Manual

Page 2: M2 dig throttle profiles, Status led order

background image

P6

throttle profile selection

m2 dig software flow chart

@NEUTRAL

BLUE-YELLOW-RED

LEDs on solid

DRAG BRAKE

BLUE & YELLOW

PROFILE

all LEDs (flashing)

DEAD BAND

BLUE & GREEN

MIN. DRIVE

YELLOW

press & hold SET button

continue holding ESC’

s SET button to skip steps here

LEDs roll off

ESC exits programming

# flashes = active profile

if pressed within 3 sec.

of all LEDs flashing

active profile changed

if not pressed within

3sec. of all LEDs flashing

VOLTAGE CUT-OFF

YELLOW-RED

DIG POWER

BLUE-GREEN-RED

DRIVE FREQ.

GREEN-RED

The M2 Dig 3S ESC features several

parameters that can be customized

to fine-tune the speed control’s feel

& response to your liking.
The flow chart below and the

adjustment steps to the right

describe the different parameters

and how they effect the ESC.
One-Touch Programming must be

completed before customization

o f p a r a m e t e r s , a s a l l E S C

parameters except Throttle Profile

are defaulted back to the factory

settings whenever the One-Touch

Programming is performed.

deFault SettiNGS FoR tHe

eSC PaRameteRS aRe liSted

iN Bold iN tHe taBleS to

tHe RiGHt

TO CHANGE PARAMETER SETTINGS:

1. CONNECT THE ESC TO A

RECEIVER AND A CHARGED

BATTERY PACK

2. SLIDE THE ESC’s ON/OFF

SWITCH TO ‘ON’ POSITION

3. WITH ESC AT NEUTRAL, PRESS

& HOLD SET BUTTON

release ESC’s SET button once LEDs

are lit for the desired setting.

To skip a parameter, continue

to press & hold SET button until

desired parameter is reached.

4. SELECT PARAMETER VALUE

LED flashes to indicate active setting

(refer to tables at right). Quick press

& release SET button to select

desired setting.

5. PRESS & HOLD SET BUTTON TO

STORE NEW SELECTION

When SET button is pressed and

held for about 1-2 seconds,

the

new selection is stored in ESC’s

memory—Status LEDs will scroll across

to indicate ESC is exiting programming

& ESC returns to neutral.

There is no time constraint during

selection of custom parameters.

NEUTRAL

BLUE-YELLOW-RED

LEDs on solid

STATUS LED ORDER:

BLUE YELLOW GREEN

RED

CUSTOM programmiNG options

The M2 Dig 3S Dual Brush speed control is equipped with

3 user-selectable

Throttle Profiles, as shown below:
• PROFILE 1 – Dig Mode – When the Aux/3rd switch/dial is thrown, the

dig function for either the front or rear motor (depending on the switch

position) will be engaged. The transmitter must have either a proportional

Aux switch or a simple three-position Aux switch.

• PROFILE 2 – Proportional Dig Mode – In this mode, the amount of dig

power applied to each motor is directly proportional to the position of the

Aux/3rd channel. The transmitter must have an Aux/3rd channel and

must have a proportional-style switch or control similar to a dial or knob.

• PROFILE 3 – Single Output Mode – This mode is used for standard two-

channel operation with either single or dual-motor control. There is no

dig function in this profile. A third channel is required for dig operation.

See

STEP 1 for proper input harness connections and STEP 3 for proper

motor connections.

NOTE: The M2 Dig has the ability to run on either 2S or3S LiPo or LiFe

batteries via Novak’s auto detect software. When the appropriate voltage

cut-off circuitry is active (see programming on reverse side to turn ON/OFF),

the ESC automatically switches to the proper cut-off voltage for the battery

pack you connect.

m2 diG tHRottle PRoFileS

BruShED MOTOr PrOFILES

1

2

3

Dig

Proportional

Single Output

Dig (default)

Reverse

100%

100%

100%

Programmable

yes

yes

yes

Drag/Hill Brake

40%

40%

40%

Dig Power

70%

70%

N/A

Dead Band

5%

5%

5%

Minimum Drive

3%

3%

3%

Drive Frequency

2.5kHz

2.5kHz

2.5kHz

Voltage Cut-Off

LiPo

LiPo

LiPo

NOTE: The M2 Dig is factory set to Profile #2

selecting throttle profiles:

all LEDs

With ESC on & connected to a charged battery (transmitter ON or OFF):
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER

To avoid possible radio interference, remove the ESC’s input signal

harness from the receiver--

green LED will stay on to indicate no signal

from receiver.

2. PRESS & HOLD THE ESC’S ONE-TOUCH SET BUTTON

Continue to hold SET button on ESC until all LEDs turn on.

Note: you will continue holding past all the LED programming

indicators in the speed control’s software as shown in the flow

chart on this sheet.

3. RELEASE SET BUTTON AS SOON AS ALL LEDs COME ON

Once released, the four status LEDs will flash to indicate what Throttle

Profile is currently selected. The number of times the LEDs flash indicates

the Brushless Throttle Profile selection (1 of 3).

4. QUICK PRESS (& release) SET BUTTON TO CHANGE SELECTION

Each press will change to the next consecutive Throttle Profile.
5. STORE SELECTION & EXIT TO NEUTRAL

Once the desired profile is selected, press and hold the SET button for 1-2

seconds. When the LEDs begin to scroll off, release the SET button and the

blue, yellow, & red LEDs will turn on solid. At this point, the ESC is at neutral

and ready to go.