Cypress CY14B108M User Manual
Page 13
PRELIMINARY
CY14B108K, CY14B108M
Document #: 001-47378 Rev. **
Page 13 of 29
Register
Description
CY14B108K
CY14B108M
0xFFFF8
0x7FFF8
Calibration/Control
D7
D6
D5
D4
D3
D2
D1
D0
OSCEN
0
Calibration
Sign
Calibration
OSCEN
Oscillator Enable. When set to 1, the oscillator is stopped. When set to 0, the oscillator runs.
Disabling the oscillator saves battery or capacitor power during storage.
Calibration
Sign
Determines if the calibration adjustment is applied as an addition (1) to or as a subtraction (0) from
the time-base.
Calibration
These five bits control the calibration of the clock.
0xFFFF7
0x7FFF7
WatchDog Timer
D7
D6
D5
D4
D3
D2
D1
D0
WDS
WDW
WDT
WDS
Watchdog Strobe. Setting this bit to 1 reloads and restarts the watchdog timer. Setting the bit to
0 has no effect. The bit is cleared automatically after the watchdog timer is reset. The WDS bit is
write only. Reading it always returns a 0.
WDW
Watchdog Write Enable. Setting this bit to 1 disables any WRITE to the watchdog timeout value
(D5–D0). This allows the user to set the watchdog strobe bit without disturbing the timeout value.
Setting this bit to 0 allows bits D5–D0 to be written to the watchdog register when the next write
cycle is complete. This function is explained in more detail in
WDT
Watchdog timeout selection. The watchdog timer interval is selected by the 6-bit value in this
register. It represents a multiplier of the 32 Hz count (31.25 ms). The range of timeout value is
31.25 ms (a setting of 1) to 2 seconds (setting of 3 Fh). Setting the watchdog timer register to 0
disables the timer. These bits can be written only if the WDW bit was set to 0 on a previous cycle.
0xFFFF6
0x7FFF6
Interrupt Status/Control
D7
D6
D5
D4
D3
D2
D1
D0
WIE
AIE
PFE
0
H/L
P/L
0
0
WIE
Watchdog Interrupt Enable. When set to 1 and a watchdog timeout occurs, the watchdog timer
drives the INT pin and the WDF flag. When set to 0, the watchdog timeout affects only the WDF
flag.
AIE
Alarm Interrupt Enable. When set to 1, the alarm match drives the INT pin and the AF flag. When
set to 0, the alarm match only affects the AF flag.
PFE
Power Fail Enable. When set to 1, the power fail monitor drives the INT pin and the
PF flag. When
set to 0, the power fail monitor affects only the PF flag.
0
Reserved for future use
H/L
High/Low. When set to 1, the INT pin is driven active HIGH. When set to 0, the INT pin is open
drain, active LOW.
P/L
Pulse/Level. When set to 1, the INT pin is driven active (determined by H/L) by an interrupt source
for approximately 200 ms. When set to 0, the INT pin is driven to an active level (as set by H/L)
until the flags register is read.
0xFFFF5
0x7FFF5
Alarm - Day
D7
D6
D5
D4
D3
D2
D1
D0
M
0
10s Alarm Date
Alarm Date
Contains the alarm value for the date of the month and the mask bit to select or deselect the date
value.
M
Match. When this bit is set to 0, the date value is used in the alarm match. Setting this bit to 1
causes the match circuit to ignore the date value.
Table 5. Register Map Detail (continued)