Braeburn 5100 - Manual (Page 4)

cont.
6
PROGRAMMING
4
Weekday Weekend
4.4 Setting Your Energy Saving Programs–Tips Before Starting
• It is important for you to set the current time of day (note the AM/PM indicator in the display),
and the current day of week correctly to avoid problems with program execution. This must be
done prior to entering any programs.
• The heating and cooling programs have both separate setpoint times and setpoint temperatures.
• This thermostat is preprogrammed with weekday and weekend setpoint times and temperatures
recommended by the Environmental Protection Agency and the U.S. Department of Energy
in their ENERGY STAR® program. These settings provide efficient energy savings during
normal heating and cooling modes of operation. If you wish to use the settings in the table,
no further programming is necessary. Review these time and temperature settings prior to
establishing your personal program settings to maximize your savings, and minimize
programming requirements.
MORN
DAY
EVE
NIGHT
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 83˚ F (28˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
Programming Overview For 7 Day Programming Mode
(Programming switch set to 7 DAY—see installation section)
You can select one of three Quick Program Groups or Individual Day programming to allow you to
change the daily setpoint times and temperatures to meet your individual schedule needs. The
Quick Program Groups can be used to set the main portion of your schedule, allowing you to later
modify specific days of the week as required using the Individual Day programming capabilities.
Once you enter program mode, you can select the Quick Program Group or Individual Day
Programs as you desire.
• Make sure you place the system switch in the HEAT or COOL modes of operation as appropriate.
You should not enter a program in the OFF position.
• When the system switch is in the COOL or HEAT modes of operation, the appropriate indicator will
appear in the LCD display when the system is running. When the system switch is in the OFF
mode, the display will indicate OFF.
Whole Week - allows you to program all seven days (M,TU, W, TH, F, SA, SU will show in
display) at the same time. Then you can use individual day programming to fine tune your
program for the few setpoint times or temperatures that you may wish to change.
Weekday - allows you to program all the weekdays (M, TU, W, TH, F will show in display) at
the same time. Then go to Weekend group mode to finish programming your weekend
setpoint times and temperatures. Individual day programming can be used to fine tune your
settings to match your daily needs.
Weekend - allows you to program all the weekend days (SA, SU will show in the display) at
the same time. Again individual day programming can be used to change specific setpoint
times or temperatures.
NOTE:
If the 7 day programming mode was selected using the slide switch on the
circuit board during installation (section 3.2), the default program will use the weekday
times and temperatures shown above for all 7 days. The programming mode can be
switched between weekday-weekend and 7 day at any time by removing the thermostat
from the base, and following steps 17-19 in section 2.2, then pressing the reset button.
All settings must then be reentered starting with section 4.2.
cont.
7
PROGRAMMING
4
Entering Your Program
1. Place the system switch in the HEAT mode of operation.
2. Press the PROG button to enter Program setting
mode. the MORN setpoint of the Whole Week Quick
Program Group will be displayed. The display will
show M, TU, W, TH, F, SA, SU, indicating the
whole week is being programmed. The hour
portion of the setpoint time and the AM/PM
indicator will be flashing.
IMPORTANT NOTE!
When in group
selection, the thermostat will check if all of the
days of that group have the same program
setpoint times and temperatures. If so, the
time and temperature of the individual setpoint
(MORN, DAY, EVE, NIGHT) will be displayed.
Otherwise, the individual setpoint time and
temperature will be blanked. User is allowed to change the daily programs for this
setpoint time and temperature by pressing the or buttons. This will reset all the
daily programs of the group for that specific individual setpoint (MORN, DAY, EVE,
NIGHT) time and temperature to the startup default for that setpoint. Continued pressing
of the or buttons by the user will change setpoint time and temperature settings
as desired.
3. If you wish to use a different Quick Program Group or Individual Day program mode you
can change by pressing the DAY/TIME button to select another group in the following
sequence, Whole Week - Weekday - Weekend - Monday - Tuesday - Wednesday
- Thursday - Friday - Saturday - Sunday - Whole Week.
4. Once you have finished your Quick Program Group or Individual Day selection. Press the
or button to change the time to the desired hour in one hour increments, press the
PROG button. The minute portion of the setpoint time will begin flashing.
5. Press the or button to change the time to the desired minute in 10-minute increments,
press the PROG button. The SET TEMP will begin flashing.
6. Press the or button to change the setpoint temperature to the desired setting in
1˚ F increments (0.5˚ C), press the PROG button. The thermostat will now display the DAY
setpoint time and temperature. Again, you will see the hour portion of the setpoint time
and the AM/PM indicator will be flashing.
7. Follow steps 4 through 6 to set the setpoint times and temperatures for the MORN, DAY,
EVE and NIGHT setpoints for the Quick Program Group or Individual Day selection for
the HEAT mode.
8. Place the system switch in the COOL mode of operation. The display will show COOL.
Follow steps 2 through 6 to program the setpoint times and temperatures for the Quick
Program Group or Individual Day selection for the COOL mode.
9. Repeat steps 3 through 8 for additional Quick Program Groups or Individual Day
programming as required.
10. After completion of programming, press RETURN or wait 15 seconds to return to the
normal mode.
Individual Days - allows you to program each day of the week individually to give you the
greatest schedule flexibility. Often used to fine tune programming after initially programming
the thermostat using Whole Week, Weekday, or Weekend groups.
Programming Overview For 7 Day Programming Mode con.