Braeburn 5000 - Manual (Page 4)

6 7
Setting the Extended Hold Time (continued) Setting Your Energy Saving Program–Tips Before Starting
• It is important for you to set the current time of day (note the AM/PM indicator
in the display), and the current day of week correctly to avoid problems with
program execution. This must be done prior to entering any program settings.
• The heating and cooling programs have both separate set point times and
set point temperatures.
• This thermostat is preprogrammed with weekday and weekend set point times
and temperatures. These settings provide efficient energy savings during normal
heating and cooling modes of operation. If you wish to use the settings in the
table, no further programming is necessary. Review these time and temperature
settings prior to establishing your personal program settings to maximize your
savings, and minimize programming requirements.
• Make sure you place the system switch in the HEAT or COOL modes of
operation as appropriate. You should not enter a program in the OFF position.
• When the system switch is in the COOL or HEAT modes of operation, the
appropriate indicator will appear in the LCD display when the system is running.
When the system switch is in the
OFF mode the display will indicate OFF.
NOTE: For 7 day programming the defaults follow the Weekday programming
shown above. To change between 5-2 and 7 day programming, adjust switch by
following step 14 of Installation section.
Entering Your Program – 5-2 Day Mode
The 5-2 Day mode has separate Weekday and Weekend Program Groups that allow
you to change the daily set point times and temperatures to meet your individual
schedule needs.
Weekday - allows you to program all the weekdays (M, TU, W, TH, F will show in
display) at the same time. Allows programming times and temperature settings for
four set points (MORN, DAY, EVE and NIGHT) to meet your weekday schedule needs.
Weekend - allows you to program all the weekend days (SA, SU will show in the
display) at the same time. Again allows programming times and temperature
settings for four set points (MORN, DAY, EVE and NIGHT) to meet your weekend
schedule needs. (continued on page 8)
2. Press the or button to change the
Extended Hold time from indefinite (
LG)
to 24 hours ( SH).
3. Press the RETURN button again to set
the Filter Check Monitor or wait 30
seconds for the thermostat to return
to the normal mode.
Setting Filter Check Monitor (see section 7)
The default setting is 0 days (Filter Monitor disabled).
1. In normal operating mode, press and
hold the
RETURN button for 4 seconds.
Press RETURN repeatedly until "XXX
FLT SET" is displayed where "XXX" is
the Filter Monitor interval (number of
days since last warning).
2. Press the or button to change the
Filter Monitor interval to the desired value of 0 (disabled), 30, 60, 90, 120, or
180 days. Press the
RETURN button again to set adaptive recovery mode or
wait 30 seconds for the thermostat to return to normal mode.
Setting Adaptive Recovery Mode (ARM™) (see section 7)
The default setting is OFF (Adaptive Recovery Mode disabled).
1. In normal operating mode, press and hold
the
RETURN button for 4 seconds. Press
RETURN repeatedly until "REC XX SE"
is displayed where
XX is the Adaptive
Recovery Mode status.
2. Press the or button to change the
Adaptive Recovery Mode to either
ON
or OFF.
3. Press the RETURN button again or wait 30 seconds for the thermostat to
return to the normal mode.
Weekday Weekend
cont.
Programming User Settings
4
Setting Your Energy Saving Program
5
MORN
DAY
EVE
NIGHT
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 62˚ F (17˚ C)
Cool: 83˚ F (28˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)
Time: 6:00 pm
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 8:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 6:00 am
Heat: 70˚ F (21˚ C)
Cool: 75˚ F (24˚ C)
Time: 10:00 pm
Heat: 62˚ F (17˚ C)
Cool: 78˚ F (26˚ C)