Maximum ratings, Operating range – Cypress HOTLink II CYV15G0104TRB User Manual
Page 17
CYV15G0104TRB
Document #: 38-02100 Rev. *B
Page 17 of 27
Maximum Ratings
(Above which the useful life may be impaired. User guidelines
only, not tested.)
Storage Temperature .................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage to Ground Potential ............... –0.5V to +3.8V
DC Voltage Applied to LVTTL Outputs
in High-Z State .......................................–0.5V to V
CC
+ 0.5V
Output Current into LVTTL Outputs (LOW)..................60 mA
DC Input Voltage ....................................–0.5V to V
CC
+ 0.5V
Static Discharge Voltage.......................................... > 2000 V
(per MIL-STD-883, Method 3015)
Latch-up Current..................................................... > 200 mA
Power-up Requirements
The CYV15G0104TRB requires one power supply. The
Voltage on any input or I/O pin cannot exceed the power pin
during power-up.
Operating Range
Range
Ambient Temperature
V
CC
Commercial
0°C to +70°C
+3.3V ±5%
CYV15G0104TRB DC Electrical Characteristics
Parameter
Description
Test Conditions
Min.
Max.
Unit
LVTTL-compatible Outputs
V
OHT
Output HIGH Voltage
I
OH
=
− 4 mA, V
CC
= Min.
2.4
V
V
OLT
Output LOW Voltage
I
OL
= 4 mA, V
CC
= Min.
0.4
V
I
OST
Output Short Circuit Current
V
OUT
= 0V
[8]
, V
CC
= 3.3V
–20
–100
mA
I
OZL
High-Z Output Leakage Current
V
OUT
= 0V, V
CC
–20
20
µA
LVTTL-compatible Inputs
V
IHT
Input HIGH Voltage
2.0
V
CC
+ 0.3
V
V
ILT
Input LOW Voltage
–0.5
0.8
V
I
IHT
Input HIGH Current
REFCLKB Input, V
IN
= V
CC
1.5
mA
Other Inputs, V
IN
= V
CC
+40
µA
I
ILT
Input LOW Current
REFCLKB Input, V
IN
= 0.0V
–1.5
mA
Other Inputs, V
IN
= 0.0V
–40
µA
I
IHPDT
Input HIGH Current with internal pull-down
V
IN
= V
CC
+200
µA
I
ILPUT
Input LOW Current with internal pull-up
V
IN
= 0.0V
–200
µA
LVDIFF Inputs: REFCLKB
±
V
DIFF
[9]
Input Differential Voltage
400
V
CC
mV
V
IHHP
Highest Input HIGH Voltage
1.2
V
CC
V
V
ILLP
Lowest Input LOW voltage
0.0
V
CC
/2
V
V
COMREF
[10]
Common Mode Range
1.0
V
CC
– 1.2V
V
3-Level Inputs
V
IHH
Three-Level Input HIGH Voltage
Min.
≤ V
CC
≤ Max.
0.87 * V
CC
V
CC
V
V
IMM
Three-Level Input MID Voltage
Min.
≤ V
CC
≤ Max.
0.47 * V
CC
0.53 * V
CC
V
V
ILL
Three-Level Input LOW Voltage
Min.
≤ V
CC
≤ Max.
0.0
0.13 * V
CC
V
I
IHH
Input HIGH Current
V
IN
= V
CC
200
µA
I
IMM
Input MID current
V
IN
= V
CC
/2
–50
50
µA
I
ILL
Input LOW current
V
IN
= GND
–200
µA
Differential CML Serial Outputs: OUTA1
±, OUTA2±, OUTB1±, OUTB2±, OUTC1±, OUTC2±, OUTD1±, OUTD2±
V
OHC
Output HIGH Voltage
(V
CC
Referenced)
100
Ω differential load
V
CC
– 0.5
V
CC
– 0.2
V
150
Ω differential load
V
CC
– 0.5
V
CC
– 0.2
V
Notes:
8.
Tested one output at a time, output shorted for less than one second, less than 10% duty cycle.
9.
This is the minimum difference in voltage between the true and complement inputs required to ensure detection of a logic-1 or logic-0. A logic-1 exists when
the true (+) input is more positive than the complement (
−) input. A logic-0 exists when the complement (−) input is more positive than true (+) input.
10. The common mode range defines the allowable range of REFCLKB+ and REFCLKB
− when REFCLKB+ = REFCLKB−. This marks the zero-crossing between
the true and complement inputs as the signal switches between a logic-1 and a logic-0.