Audio output, Action, Action шее \o – Panasonic PV-D4752 User Manual
Page 46: Press, Press at to select “audio output,’ and press, Press at to select an item, and press, Repeatedly for output. (see below.), Dvd), Dolby digital” selections bitstream, Dts” selections bitstream
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Audio Output
I
Select the digital output to be output from the optical
digital audio output connector of DECK.
1
Press
ACTION*
to display MENU.
_______
__ Ready Checklist
□ DECK is in DVD mode, press DVD.
SELECT
SET
END
Press AT
to select
“AUDIO OUTPUT,’
and
press
SET
to display screen.
AUDIO OUTPUT
. Digital
dts
DRC
SURROUND
SELECT
SET
END
Press AT
to select an item,
and
press
SET
repeatedly for
output. (See below.)
■ “LPCM
(DVD)”
selections
OFF-
Linear PCM of less than 48 kHz/16 bit is
output. When playing DVDs recorded in
linear PCM of over 48 kHz/20 bit or 96 kHz,
no digital audio is output. (Factory presep
PCM:
When playing DVDs recorded in linear PCM
of 48 kHz/20 bit/24 bit or 96 kHz, digital
audio converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright
protection.)
■ “Dolby Digital” selections
Bitstream:
Dolby Digital bitstream (1ch-5.1ch) is
output. (Factory preset)
OFF:
No output.
■ “dts” selections
Bitstream:
dts bitstream is output. (Factory preset)
OFF:
No output.
_
■ “DRC (Dynamic
Range
Compression)” selections
ki_______I
^-1 io colontpH ^FaritOrV
ON
Normal audio range is selected. (Factory
preset)
,
...
For dynamic sound even at low volume, this
is useful for late-night listening. [Dolby Digital
DVDs only).
I “SURROUND” selections
Surround Sound creates the effect of sound corning
from non-existent rear speakers even when only
connected to a
2
-channel stereo system.
OFF:
No Surround Sound effect. (Factory preset)
ON:
Surround Sound effect.
__________
Type of amplifier
to be connected
Recommended setting
LPCM
(DVD)
Dolby
Digital
dts
No amplifier is connected
OFF
OFF
OFF
AV amplifier (with digital
audio input connector)
without Dolby Digital/dts
decoder
PCM*''
0
FF
*2 0
FF
*2
AV amplifier including
Dolby Digital decoder
PCM*''
Bitstream
OFF
AV amplifier including
Dolby Digital/dls decoder
PCM*'
Bitstream
*3
Bitstream
• Make settings according to amplifier
connected to optical audio output as shown
in above table.
• When a dts decoder is not connected, to
enjoy dts DVD, please select audio output
other than dts at the dts DVD menu screen.
Otherwise, there will be no sound.
*1 Audio Output 2 from DECK is converted to
48 kHz/16 bit in addition to audio from
digital audio output.
To enjoy high quality sound at 48 kHz/20
bit /24 bit or 96 kHz, connect the amplifier
or decoder directly to the Audio Output 2
connectors, not to the Digital Audio Output
connector. [Select “OFF” at the “LPCM
(DVD)”.]
*2 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or dts
decoder, be sure to select “OFF”,
if “Bitstream” is selected, starting DVD play
may cause such a high level of noise as to
be harmful to your ears and damage the
speakers.
*3 When a dts decoder is connected, please
select “Bitstream” in “dts”. If “OFF” is
selected, there will be no sound.
Press
ACTION
to redisplay DVD menu
and go to step 2 to setup another item.
Or, press
ACTION Шее \o
exit.
• Turn off other surround effects when using
this surround effect.
• For optimum effect, the distance between
DECK and the listener should be about 3 or 4
times the distance between the right and left
front speakers.
46
For
assistance, please call
: