Panasonic CQ-VX777EW - Manual (Page 41)

Tone Quality Adjustment/HEQ Setting
O SEL, ©
A, V, <, >, © SPC, © preset 1, ©
preset 2 button
1. HEQ Switching
Equalizer modes change as follows each time
SEL is pressed.
Normal Mode (VOL) -4 HEQ ^ GEQ ^ BAL/FAD
t i
Preout 4- DRCH <- SBC/SBC-SW <- Position
2. Selecting Desired Tone Quality
Select a desired tone quality using A, V, <, >.
With the center fixed flat, any of the 49
- equalizer patterns, arranged in vertical and
horizontal directions, can be selected.
3. Selecting Desired Sound Field Effect
Press SPC to select a desired sound field
effect.
1. Press 1 to narrow the sound field
(steps 1 to 3).
2. Press 2 to widen the sound field
(steps 1 to 3).
GEQ Setting
© S E L , © A,V,<,>
• Press SEL to select GEQ mode.
• Press <, > (frequency up/down) to select a
frequency.
• Press A to raise the level.
Press V to lower the level.
L
GEQ Memory
© SEL, © operation buttons , © SPACE , ©
preset 1, © prese 2, © preset 3, © preset 4,
© preset 5, © preset 6
1. Select GEQ.
2. Select a desired equalizer characteristic.
3. Press one of the memory buttons for more
than 2 seconds.
4. The preset number flashes, indicating that the
selected equalizer characteristic has been
saved in the memory.
GEQ Memory Recall
© SEL, © operation buttons , © SPACE ,©
preset 1, © prese 2, © preset 3,0 preset 4,
© preset 5 , © preset 6
1. Press SEL to select GEQ.
2. Press one of the memory buttons.
TUNER (RADIO)
Selecting Tuner Mode
0 AM/FM button
If the mode is other than tuner mode, press this
button to change it to tuner mode.
Switching Bands
0 AM/FM button
The AM and FM bands change alternately each
time this button is pressed.
Tuning (Manual)
©ATUNE,®TUNEV
Press A to raise the frequency.
Press V to lower the frequency.
Automatic Seek
0 ATUNE,©TUNEV
When either of these buttons is pressed for more than 0.5
second, the frequency changes till a station is tuned in to,
where the frequency stops automatically. Repeat it till a
desired station is received.
Preset Memory
0 AM/FM, 0 ATUNE, 0TUNEV, 0 preset 1,
© prese 2, © preset 3,© preset 4 , © preset
5 , © preset 6
0 Band Switching
Press AM/FM to select the AM or FM band as
desired.
0 Tuning
Press A TUNE or TUNEV to tune in to a desired
station.
(D Preset Button Memory
After tuning in to a desired station by steps ©
and
Q) above, press one of the preset buttons t to
6 for 2 seconds so the frequency indicator flashes.
It indicates that the station has been preset in the
memory. Repeat it from FM1 to AM2.
Preset Tuning
© preset 1, © prese 2, © preset 3,© preset
4 , © preset 5 , © preset 6
I When one of the buttons 1 to 6 preset in the
memory is pressed, the corresponding preset
station is tuned in to.
Auto Preset Memory
0 AM/FM, © ATUNE, 0 TUNEV, © preset
1, © prese 2, © preset 3,0 preset 4, ©
preset 5,0 preset 6
• When AM/FM (AUTO PRESET) is pressed for more
than 2 seconds, frequency search begins with the
lowest of the frequencies on the band being
received, and up to 6 stations are automatically
stored in the preset memory in the order of signal
intensity.
• After search, the preset stations are received for 5
seconds each in order.
• When you find a station you wish to listen to, press
the corresponding button among preset buttons 1 to
41
CQ-VX777EW