Dataram DRH380G4 - Manual (Page 2)

MEMORY REMOVAL
Note: Refer to your system owner’s manual for detailed instructions. MEMORY INSTALLATION
3.
Open both ejector levers on each slot.
4. Position a module over the slot so that the alignment notches on the
DIMM match the notches on the connector.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
grounded wrist strap.
5.
Press firmly with your thumbs on both top ends of the module, applying
equal pressure until the module snaps into place. Lock the module in the
socket by pushing up on the ejector levers until they are in their upright
position.
1. The table below reflects the only valid configurations for the ProLiant
DL380 G4. Bank A reflects DIMM slots 1A and 2A, Bank B reflects DIMM
slots 3B and 4B, & Bank C reflects DIMM slots 4C and 5C.
Bank A Bank B Bank C NOTES
SINGLE RANK EMPTY EMPTY
SINGLE RANK SINGLE RANK EMPTY
SINGLE RANK SINGLE RANK SINGLE RANK
Online Spare not
supported
DUAL RANK EMPTY EMPTY
Online Spare not
supported
2.
The ProLiant ML370 G4 has four banks of memory, identified as 1A and
2A, 3B and 4B, 5C and 6C, and 7D and 8D. DIMMs are installed
beginning with slots 1A and 2A. Do not skip any slots.
DUAL RANK SINGLE RANK EMPTY
Caution: Confirm the modules are fully and evenly seated in the slots.
Improper seating can cause electrical shorts that can damage
the memory and/or the system. Online Spare not
supported
DUAL RANK SINGLE RANK SINGLE RANK
Online Spare not
supported
DUAL RANK DUAL RANK EMPTY
6.
Continue to install the remaining memory modules until you have filled
the bank with two identical modules. Repeat the above steps for each
bank of memory you wish to install.
7.
Reconnect the power cords and external cables, and turn on the system.
8. After you reboot, ensure the system recognizes the new memory
configuration.
MEMORY REMOVAL MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions. 3. Open both ejector levers on each slot.
4. Position a module over the slot so that the alignment notches on the
DIMM match the notches on the connector.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
grounded wrist strap.
5.
Press firmly with your thumbs on both top ends of the module, applying
equal pressure until the module snaps into place. Lock the module in the
socket by pushing up on the ejector levers until they are in their upright
position.
1. The table below reflects the only valid configurations for the ProLiant
DL380 G4. Bank A reflects DIMM slots 1A and 2A, Bank B reflects DIMM
slots 3B and 4B, & Bank C reflects DIMM slots 4C and 5C.
Bank A Bank B Bank C NOTES
SINGLE RANK EMPTY EMPTY
SINGLE RANK SINGLE RANK EMPTY
SINGLE RANK SINGLE RANK SINGLE RANK
Online Spare not
supported
DUAL RANK EMPTY EMPTY
Online Spare not
supported
2.
The ProLiant ML370 G4 has four banks of memory, identified as 1A and
2A, 3B and 4B, 5C and 6C, and 7D and 8D. DIMMs are installed
beginning with slots 1A and 2A. Do not skip any slots.
DUAL RANK SINGLE RANK EMPTY
Caution: Confirm the modules are fully and evenly seated in the slots.
Improper seating can cause electrical shorts that can damage
the memory and/or the system. Online Spare not
supported
DUAL RANK SINGLE RANK SINGLE RANK
Online Spare not
supported
DUAL RANK DUAL RANK EMPTY
6.
Continue to install the remaining memory modules until you have filled
the bank with two identical modules. Repeat the above steps for each
bank of memory you wish to install.
7.
Reconnect the power cords and external cables, and turn on the system.
8. After you reboot, ensure the system recognizes the new memory
configuration.