Great Plains 2025P Operator Manual User Manual
Page 94

2025P, 2020P Bedded, and
2010HDP
118-928M
8/14/2006
92
Crop
Row Spacing Number of cells Min. Rate
Max. Rate
Cal #
Corn
20”
28
20500
37000
1751
Corn
30”
28
20500
37000
1167*
Corn
38”
28
20500
37000
921*
Corn
15” Rows or TR30
28
20500
37000
2334
Corn
19”Rows or TR 38”
28
20500
37000
1843
Corn
20”
42
31000
55600
2626
Corn
30”
42
31000
55600
1751*
Corn
38”
42
31000
55600
1382*
Corn
15” Rows or TR30
42
31000
55600
3501
Corn
19”Rows or TR 38”
42
31000
55600
2764
Cotton
9.5”
120
58500
159000
15796
Cotton
10”
120
58500
159000
15006
Cotton
15” Rows or TR30
120
58500
159000
10004
Cotton
19”Rows or TR 38”
120
58500
159000
7898
Cotton
TR 30” W/Splitters
120
58500
159000
15006
Cotton (HR)
9.5”
120
117000
318000
15796
Cotton (HR)
10”
120
117000
318000
15006
Cotton (HR)
15” Rows or TR30
120
117000
318000
10004
Cotton (HR)
19”Rows or TR 38”
120
117000
318000
7898
Cotton (HR)
TR 30” W/Splitters
120
117000
318000
15006
Row Cotton
20”
120
29000
79500
7503
Row Cotton
30”
120
29000
79500
5002*
Row Cotton
38”
120
29000
79500
3949*
Row Cotton
15” Rows or TR30
120
29000
79500
10004
Row Cotton
19”Rows or TR 38”
120
29000
79500
7898
Row Milo (LR)
20”
102
24900
67600
66378
Row Milo (LR)
30”
102
24900
67600
4252*
Row Milo (LR)
38”
102
24900
67600
3357*
Row Milo (LR) 15” Rows or TR30
102
24900
67600
8504
Row Milo (LR) 19”Rows or TR 38”
102
24900
67600
6713
Row Milo (MR)
20”
135
32300
89500
8441
Row Milo (MR)
30”
135
32300
89500
5627*
Row Milo (MR)
38”
135
32300
89500
4443*
Row Milo (MR) 15” Rows or TR30
135
32300
89500
11255
Row Milo (MR) 19”Rows or TR 38”
135
32300
89500
8885
Row Milo (HR)
20”
270
65300
178900
16882
Row Milo (HR)
30”
270
65300
178900
11255*
Row Milo (HR)
38”
270
65300
178900
8885*
Row Milo (HR) 15” Rows or TR30
270
65300
178900
22509
Row Milo (HR) 19”Rows or TR 38”
270
65300
178900
17771
Solid Milo (LR)
9.5”
51
24900
67500
6713
Solid Milo (LR)
10”
51
24900
67500
6378
Solid Milo (LR) 15” Rows or TR30
51
24900
67500
4252
Solid Milo (LR) TR 30” W/Splitters
51
24900
67500
6378
Solid Milo (MR)
9.5”
102
49800
135000
13427
Solid Milo (MR)
10”
102
49800
135000
12755
Solid Milo (MR) 15” Rows or TR30
102
49800
135000
8504
Solid Milo (MR) TR 30” W/Splitters
102
49800
135000
12755
Solid Milo (HR)
9.5”
135
65900
178900
17771
Solid Milo (HR)
10”
135
65900
178900
16882
Solid Milo (HR) 15” Rows or TR30
135
65900
178900
11255
Solid Milo (HR) TR 30” W/Splitters
135
65900
178900
16882
Soybeans
9.5”
100
140000
265000
13163
Soybeans
10”
100
140000
265000
12505
Soybeans
20”
100
140000
265000
6253
Soybeans
30”
100
140000
265000
4168*
Soybeans
38”
100
140000
265000
3291*
Soybeans
15” Rows or TR30
100
140000
265000
8337
Soybeans
19”Rows or TR 38”
100
140000
265000
6582
Soybeans
TR 30” W/Splitters
100
140000
265000
12505
Soybeans
9.5”
110
140000
291000
14480
Soybeans
10”
110
140000
291000
13756
Soybeans
20”
110
140000
291000
6878
Soybeans
30”
110
140000
291000
4585*
Soybeans
38”
110
140000
291000
3620*
Soybeans
15” Rows or TR30
110
140000
291000
9171
Soybeans
19”Rows or TR 38”
110
140000
291000
7240
Soybeans
TR 30” W/Splitters
110
140000
291000
13756
Soybeans
15” Skip Row 5/4/5
100
140000
291000
7295
Soybeans
15” Skip Row 5/4/5
110
140000
291000
8024
NOTE: Cal number
should be accurate for
singulated meters, but
Great Plains strongly
suggests that you use
the Calibration Routine
to fine-tune your actual
seeding rate.
* Extremely high rates
using these meters on
this row spacing may re-
quire lower ground
speed; see GP Manual
for additional
information.
NOTE: For proper oper-
ation of the Great Plains
Singulator Plus Meter
used on the 20 and 25
series openers the 12
tooth drive sprocket is
required on the Veris
drive on both sides of
the drill. To change to
the 12 tooth sprocket re-
fer to “Veris Drive
Sprocket Change” on
page 91.
Calibration Table-Singulating (Low Range)
Motor 12T Driver-Mainshaft 36T Driven