E-flite Power 15 Brushless Outrunner Motor, 950Kv - Manual (Page 3)

Safety Precautions:
This is a sophisticated hobby product and not a toy. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other
property. This product is not intended for use by children without direct adult supervision. The Outrunner motor case is a
rotating part so use extreme caution. Please read the warning information included with your propellers for safety information related to
the operation of motors with propellers. Failure to comply with these warnings and/or improper use of propellers may result in serious
injury.
Installation:
NOTE: Photo shows typical installation of motor and x-mount directly to the outside of the firewall. There are other options available
including mounting the motor inside the fuselage (requires reversing the shaft direction) or extending the motor further forward using
aftermarket mount extensions when using cowls.
1. You can first trial fit the aluminum x-mount against the front of the firewall and use a Sharpie® to mark the locations of four holes
and drill appropriate size hole to fit the blind nuts provided. Always be sure to maintain the proper thrust line and account for
adequate prop/spinner clearance.
2. Attach aluminum x-mount to the outrunner motor using the four flat head (countersunk) screws provided with the motor.
3. Install four blind nuts on the inside of the firewall.
4. Attached the aluminum x-mount and motor to the outside of the firewall using the four socket head cap screws and washers.
NOTE: Photo above shows installation using nylon motor standoffs.
1. Attach the aluminum x-mount to the back of your motor with the flat head machine screws included with your motor.
2. Choose a standoff length that will allow for proper clearance of your propeller once the cowl is attached. You may want to trial fit
the cowl to make this determination.
3. Insert appropriately sized socket head screws and washers into the four outside holes on the x-mount, through the standoffs, and
then attached to blind nuts in the firewall.
WARRANTY AND REPAIR POLICY
Limited Warranty Period:
Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the "Product") will be free from defects in materials and workmanship for a period of
1 year from the date of purchase by the Purchaser.
Limited Warranty:
(a) This warranty is limited to the original Purchaser ("Purchaser") and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased from an authorized Horizon
dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims. Horizon reserves the right to change or
modify this warranty without notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE
HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy - Horizon's sole obligation hereunder shall be that Horizon will, at its option, (i) repair or (ii) replace, any Product determined by
Horizon to be defective. In the event of a defect, these are the Purchaser's exclusive remedies. Horizon reserves the right to inspect any and all equipment
involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This warranty does not cover cosmetic damage or
damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not
cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return of any goods by Purchaser
must be approved in writing by Horizon before shipment.
Damage Limits:
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is
asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting