E-flite 10-Amp Pro Brushless ESC - Manual (Page 2)

(continued)
5. When you have made a valid selection the control will beep once with
a lower tone, and you can move the stick back to center for the next
menu item (2 beeps, 3 beeps and so on). If you do not make a
selection within 5 seconds, the controller will move to the next
menu item.
6. Please note that if you do not need to program every menu item, you
can simply exit the programming mode after you have made the
required selections. You can do this by moving the throttle stick
straight to Idle, after making your selection, or leaving it in the Idle
position if you made a no selection (for approximately 8 seconds), until
you hear one set of 3 medium length rising tones that indicate the
controller has armed the motor, or by simply unplugging the battery.
Remember, when in the programming mode:
Full Throttle = Stick Up
Idle = Stick Down
The default settings (from the package) for your
E-flite 10-Amp Pro ESC are as follows:
• 3S (9V) auto cut-off for Li-Po
• Brake Off
• 4-pole and greater timing (outrunner or 6-pole motors)
• Throttle input range set to Auto Select Mode
(1.2ms-1.8ms)
Programming Menu 1 – Voltage Cut-off
Use this option to set the voltage at which the controller will shut down
the motor to prevent damage to your battery, when it reaches the cut-off
voltage. You will know that your battery pack has reached auto cut-off
when you hear the motor “pulse” repeatedly.
1. 3S Li-Po voltage cut-off – Full Throttle
2. 2S Li-Po or Ni-Cd/Ni-MH voltage cut-off – Idle
3. 70% Smart Cut soft cut-off (See below for Smart Cut information)
NOTE: To access the 70% Smart Cut option, leave the stick at full throttle for 7 seconds while in menu
item 1, until 7 beeps are heard, then continue through the program normally. This option will activate the
soft cut-off at 70% of startup voltage. For example, if your pack measures 10.0 volts at startup, then the
soft cut will occur at 7.0 volts. The Smart Cut option will check the startup voltage every time you plug the
battery into the controller, so beware of using partially charged packs, as the system cannot protect your
Li-Po batteries if you are using Smart Cut and connect a partially charged pack.
You will know your battery pack has reached soft auto cut-off when you
hear the motor “pulse” repeatedly. We recommend you land your model as
soon as you hear the motor pulse (indicating the pack voltage has dropped
to the cut-off voltage level) to prevent over-discharge of the Li-Po battery
pack, and to prevent sudden power loss.
Programming Menu 2 – Braking
This option gives you the choice to have the ESC stop the propeller during
flight (Brake on) or allow it to windmill (Brake off). Use the brake-on option
for gliders.
1. Brake Off – Full Throttle (>1.7ms)
2. Brake On – Idle (<1.3ms)
Programming Menu 3 – Timing
Please refer to your motor instructions and specifications for an indication
of the number of poles.
1. 4 pole and greater motors timing mode – Full Throttle
2. 2 pole motors timing mode – Idle
Programming Menu 4 – Throttle Input Range
This option is to allow for proper operation of the ESC with many different
radios on the market. Most radios, and all the computer radios we have
tested, work well with the auto-set option, but some radios have a wider
output range, and may give a more linear response with the 1.1 to 1.9ms
range. If you feel there is too much “dead” area in the stick movement
near Full Throttle, try adjusting the end points in your radio, or change to
the wider input range. Be aware that if these settings are not correct, it
may be impossible to arm the controller. If this happens, return the input
range setting to the default auto learning setting.
The auto setting option learns the minimum position of your throttle
(between 1.1 and 1.3ms) and stores this value at each startup, and then
adds a value of 0.6ms for the full throttle setting.
1. Throttle Range 1.1ms to 1.9ms – Full Throttle
2. Auto Select – Idle
Error Codes
The controller will beep continuously if the input voltage is below the cut
voltage (beep...beep...beep) when the battery is connected. Check the
voltage of the battery pack to see if it is correct, or the programmed cut-off
setting if the input voltage is set incorrectly for the voltage of the pack
being used.
If you have trouble arming the controller (and the throttle trim has been
set to minimum), enter the programming mode and try the auto setting in
Programming Menu 4 to see if it helps correct your problem. If it is a
computer radio, you may alternatively increase your high and low throttle
ATV (endpoint) percentages.
Some systems including many Futaba systems may require the throttle
channel to be “reversed” for proper operation.
Limited Warranty Period
Horizon Hobby, Inc. guarantees this product to be free from defects in both
material and workmanship for a period of 1 year from the date of purchase.
Limited Warranty & Limits of Liability
Pursuant to this Limited Warranty, Horizon Hobby, Inc. will, at its option,
(i) repair or (ii) replace, any product determined by Horizon Hobby, Inc.
to be defective.
In the event of a defect, these are your exclusive remedies.
This warranty does not cover cosmetic damage or damage due to acts of
God, accident, misuse, abuse, negligence, commercial use, or modification
of, or to any part of the Product. This warranty does not cover damage due
to improper installation, operation, maintenance, or attempted repair by
anyone other than an authorized Horizon Hobby, Inc. service center. This
warranty is limited to the original purchaser and is not transferable. In no
case shall Horizon Hobby’s liability exceed the original cost of the
purchased product and will not cover consequential, incidental or collateral
damage. Horizon Hobby, Inc. reserves the right to inspect any and all
equipment involved in a warranty claim. Repair or replacement decisions
are at the sole discretion of Horizon Hobby, Inc. Further, Horizon Hobby,
Inc. reserves the right to change or modify this warranty without notice.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE EXCLUSIVE REMEDY OF THE CONSUMER. HORIZON HOBBY, INC.
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
As Horizon Hobby, Inc. has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed nor accepted for any
resulting damage or injury. By the act of use, setup or assembly, the user
accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the liability
associated with the use of this product, you are advised to return this
product immediately in new and unused condition to the place of
purchase.
Safety Precautions
This is a sophisticated hobby product and not a toy. It must be operated
with caution and common sense and requires some basic mechanical
ability. Failure to operate this product in a safe and responsible manner
could result in injury or damage to the product or other property.
This
product is not intended for use by children without direct adult supervision.
For complete and specific information concerning the Limited Warranty,
Limits of Liability, and Safety Precautions – please refer to our web-page
for this item or contact your E-flite distributor. You can also direct emails
to [email protected], or in the U.S., call 877.504.0233
toll free to speak to a service technician.
Made in China
© 2006 Horizon Hobby, Inc.
www.horizonhobby.com
www.E-fliteRC.com
E-flite ® is an exclusive brand of Horizon Hobby, Inc.
9194