Hinkley Lighting BELDEN PLACE 2862 - Manual (Page 2)

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com
I.S. 19-92
hanging instruction
Item No. 4224

start here
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS
(IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF
DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A
QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE
REQUIREMENTS.
1. Shut off electrical current before starting. If the fixture you
are replacing is turned on and off by a wall switch, simply turn
the switch off. If not, remove the appropriate fuse (or open
the circuit breakers) until the fixture is dead.
 DO NOT restore current --- either by fuse, breaker, or switch ---
until the new fixture is completely wired and in place.
1. Determine the desired height the chandelier will be installed.
2. The fixture is supplied with assorted stem sizes. Determine
what combinations of stems are needed to achieve desired
length --- see Drawing 1.
3. Slip stems over wire and thread first stem into coupler on top
of chandelier, longest stem first. Repeat this process until all
required stems are threaded together.
4. Slip wire through center of canopy swivel and thread onto
stem assembly.
1. Thread two long 8-32 screws (1) into the mounting strap (2).
NOTE: The two screws should be threaded into the holes
that line up with the holes in the canopy (3) --- see Drawing
2.
2. Attach the mounting strap (2) to the junction box with two 8-
32 screws (5).
3. Make wire connections following the instructions on (IS 18)
instruction sheet provided.
4. Assistance is recommended for the follow process.
5. Lift assembled fixture with stems and canopy up to ceiling and
slip screws (1) through holes in canopy (3). Secure fixture to
mounting strap by threading ball knobs (4) onto end of
screws (1) and tighten.
I.S. 19-92
pendaison instruction
Item No. 4224

commencez ici
AVERTISSEMENT DE SECURITE: LIRE CABLAGE ET INSTRUCTIONS DE
MISE (IS 18), ET TOUTE AUTRE INSTRUCTION. COUPER
L’ALIMENTATION ELECTRIQUE PENDANT L’ONSTALLATION. SI DE
NOUVELLES CABLAGE N’EST NECESSAIRE, CONSULTEZ UN
ELECTRICIEN QUALIFIE OU AUTORITES LOCALES POUR EXIGENCES DU
CODE.
1. Couper le courant ékectrique avant de commencer. Si l’appareil
vous remplacez est activeé et désactivé par un interrupteur mural,
il suffit de tourner l’interrupteur. Sinon, retirez le fusible
approprié *ou ouvrez les disjoncteurs) jusqu’á ce que l’appareil
est mort.
 NE PAS restaurer actuel --- soit par fusible, disjoncteur,
interrupteur ou --- justqu’á ce wue le nouvel appareil est
entiérement câblé et en place.
1. Déterminer la hauteur désirée du luster sera installé.
2. L’appareil est fourni avec des tailles de souches variées.
Déterminer quelles combinaisons de tiges sont nécessaires pour
atteindre la longuer désirée --- Voir Schéma 1.
3. Slpi tient sur le fil et le fil premiére tige dans le coupleur sur le
dessus du lustre, tige la plus longue premier. Répétez cette
opération jusqu’á ce que toutes les tiges nécessaires sont enfilées.
4. Glisser le fil par le centre de pivotement de la canopée et du fil
sur l’assemblage de la tige.
1. Thread two long 8-32 screws (1) into the mounting strap (2).
NOTE: The two screws should be threaded into the holes that
line up with the holes in the canopy (3) --- see Drawing 2.
2. Attach the mounting strap (2) to the junction box with two 8-32
screws (5).
3. Make wire connections following the instructions on (IS 18)
instruction sheet provided.
4. Assistance is recommended for the follow process.
5. Lift assembled fixture with stems and canopy up to ceiling and
slip screws (1) through holes in canopy (3). Secure fixture to
mounting strap by threading ball knobs (4) onto end of screws (1)
and tighten.
I.S. 19-92
colgando de instrucciones
Item No. 4224

empezar aquí
ADVERTENCIA DE SEGURIDAD: LEA LAS INSTRUCCIONES DE CABLEADO
Y LA TIERRA (IS 18), E INSTRUCCIONES ADICIONALES. APAUGE LA
ALIMENTACIÓN DE CORRIENTE DURANTE LA INSTALACIÓN. SI SE
REQUIERE NUEVO CABLEADO, CONSULTE CON UN ELECTRICISTA O
AUTHORIDADES LOCALES PARA REQUISITOS DEL CÓDIGO.
1. Apague la corriente eléctrica antes de comenzar. Si el aparato
va a sustituir se enciende y se apaga por un interruptor de
pared, simplemente gire el interrupor. Si no es así, quite el
fusible adecuado (o abra los interruptores de circuito) hasta
que el aparato está muerto.
 No restaurar actual --- ya sea mediante fusible, disyuntor o
interruptor --- hasta que el nuevo dispositivo está
completamente conectdo y en su lugar.
1. Determine the desired height the chandelier will be installed.
2. The fixture is supplied with assorted stem sizes. Determine what
combinations of stems are needed to achieve desired length --- see
Drawing 1.
3. Slip stems over wire and thread first stem into coupler on top of
chandelier, longest stem first. Repeat this process until all required
stems are threaded together.
4. Slip wire through center of canopy swivel and thread onto stem
assembly.
1. Thread two long 8-32 screws (1) into the mounting strap (2).
NOTE: The two screws should be threaded into the holes that
line up with the holes in the canopy (3) --- see Drawing 2.
2. Attach the mounting strap (2) to the junction box with two 8-32
screws (5).
3. Make wire connections following the instructions on (IS 18)
instruction sheet provided.
4. Assistance is recommended for the follow process.
5. Lift assembled fixture with stems and canopy up to ceiling and slip
screws (1) through holes in canopy (3). Secure fixture to mounting
strap by threading ball knobs (4) onto end of screws (1) and
tighten.
Drawing 1 – Fixture Mounting
Drawing 2 – Glass Installation