Motor load force ratings – Rockwell Automation MPL-xxxx Low Inertia Servo Motor 215 mm or Larger User Manual
Page 16
16 MP-Series Low-inertia Servo Motor with 215 mm or Larger Frame Size
Rockwell Automation Publication MP-IN002D-EN-P - January
Dimensions (continued)
Motor Load Force Ratings
Motors are capable of operating with a sustained shaft load. The load force locations are shown
in the figure and maximum values are in the tables.
Loads are measured in kilograms; pounds are mathematical conversions.
Load Forces on Shaft
The following tables represent 20,000 hour L
10
bearing fatigue life at various loads and speeds.
This 20,000 hour life does not account for possible application-specific life reduction that can
occur due to bearing grease contamination from external sources.
Motor
Cat. No.
LB
(1)
mm (in.)
(1)
For motors with a brake, for example MPL-Bxxx-xxx4AA, add to MPL-B6xx dimensions LB, LD. and LE: 108.0 mm (4.25 in.); to MPL-B8xx
dimensions LB, LD. and LE:107.9 mm (4.26 in.); and to MPL-B9xx dimensions LB, LD 127.0 mm (5.0 in.).
LD
(1)
mm (in.)
LE
(1)
mm (in.)
M
mm (in.)
N
(2)
mm (in.)
(2)
Tolerance for the dimension is MPL-B6xx +0.014, -0.011 mm, (+0.0005, -0.0005 in.); MPL-B8xx +0.016, -0.013 mm, (+0.0006, -0.0005 in.);
MPL-B9xx +0.016, -0.013 mm, (+0.0005, -0.0006 in.).
P
mm (in.)
S
(3)
mm (in.)
(3)
Tolerance for the dimension is MPL-B6xx +0.43 mm (±0.008 in.); MPL-B8xx and MPL-B9xx +0.52 mm (±0.010 in.).
T
mm (in.)
Shaft End
Threaded Hole
mm (in.)
MPL-B640
223.8
(8.81)
183.6
(7.23)
112.5
(3.15)
215.0
(8.465)
180.0
(7.0867)
184.9
(7.28)
14.50
(0.579)
3.73
(0.147)
M12 x 1.75- 6H
thread depth
28 (1.10)
MPL-B660
274.6
(10.81)
234.4
(9.23)
163.3
(6.43)
MPL-B680
325.4
(12.81)
285.2
(11.23)
214.1
(8.43)
MPL-B860
284.4
(17.45)
242.6
(9.55)
171.4
(6.75)
265.0
(10.433)
230.0
(9.0551)
230.0
(9.25)
3.86
(0.152)
M16 x 2- 6H
thread depth
36 (1.42)
MPL-B880
335.2
(13.20)
293.4
(11.55)
222.2
(8.75)
MPL-B960
293.3
(11.55)
248.9
(9.80)
177.9
(7.0)
300.0
(11.811)
250.0
(9.8426)
266.7
(10.50)
18.50
(0.738)
4.88
(0.192)
M16 x 2- 6H
thread depth
36 (1.42)
MPL-B980
344.1
(13.55)
299.7
(11.80)
228.7
(9.0)
Axial Load Force
Radial load force applied at center of shaft extension.