Rockwell Automation 1609-B_D UPS Product User Manual User Manual
Bulletin 1609 uninterruptible power supply
Table of contents
Document Outline
- Important User Information
- Preface
- Table of Contents
- -Bulletin 1609-D Installation Instructions
- Battery Wiring and Installation
- 1. To access the battery compartment remove the three screws and the battery door.
- 2. Remove the battery container, jumpers, and wire harness from the battery compartment. Place the battery container and batteries onto a flat surface. Use the provided jumper wires to connect the batteries in series. Connect the positive terminal (r...
- 3. Connect the red wire of the harness to the positive terminal (top red) and the black wire of the harness to the negative terminal (bottom black). See photo below for details.
- Battery Wiring and Installation (cont.)
- 4. Fold the battery container and seal it with tape.
- 5. To connect the batteries to the UPS, insert the batteries into the battery compartment, open the white connector retainer and connect the two cables together as shown in the photo below.
- 6. To complete the battery installation, close the white connector retainer and reattach the battery door with the three screws (torque of 8.7+/-1.7 lb-in).
- Mount the UPS
- Hardwire UPS
- Selection of Cables
- Connect Power and Equipment to the UPS
- 1609-D Block Figure
- Battery Wiring and Installation
- 1609-B Installation Instructions
- Battery Wiring and Installation
- 1. To access the battery compartment remove the three screws and the battery door.
- 2. Remove the battery container, jumpers, and wire harness from the battery compartment. Place the battery container and batteries onto a flat surface. Use the provided jumper wires to connect the batteries in series. Connect the positive terminal (r...
- 3. Fold the battery container and seal it with tape.
- Battery Wiring and Installation (cont.)
- 4. To connect the batteries to the UPS, insert the batteries into the battery compartment, open the white connector retainer and connect the two cables together as shown in the photo below.
- 5. To complete the battery installation, close the white connector retainer and reattach the battery door with the three screws (torque of 8.7+/-1.7 lb-in).
- Mount the UPS
- Hardwire UPS
- Selection of Cables
- Connect Power and Equipment to the UPS
- 1609-B Block Figure
- Battery Wiring and Installation
- 1609-EXBAT Installation Instructions
- Battery Wiring and Installation
- 1. To access the battery compartment remove the six screws and the battery door.
- 2. Remove the battery container, jumpers and wire harness from the battery compartment. Place the battery container and batteries onto a flat surface. Use the provided jumper wires to connect the batteries in series. Connect the positive terminal (re...
- Battery Wiring and Installation (cont.)
- 3. Connect the shorter set of red and black wires of the harness to the top terminals (red - to - red and black - to - black). Connect the longer set of red and black wires of the harness to the bottom terminals (red - to - red and black - to - black...
- 4. Fold the battery container and seal it with tape.
- 5. Insert the batteries into the battery compartment in the orientation as shown in the photo below.
- 6. Open the white connector retainer and connect the two cables together as shown in the photo below.
- Battery Wiring and Installation (cont.)
- Mount the 1609-EXBAT
- Selection of Cables
- Connect 1609-EXBAT to the UPS
- Battery Wiring and Installation
- General Information 1609-D and 1609-B UPS Units
- Troubleshooting
- Appendix A
- 1609 UPS Dimensions
- 1609-D UPS Dimensions
- 1609-B UPS Dimensions
- 1609-EXBAT Unit Dimensions
- 1609-BRK Dimensions (1609-D orientation)
- 1609-BRK Dimensions (1609-B orientation)
- Service Instructions
- 1. Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from batteries.
- 2. When replacing batteries, replace with the same number of the 1609 battery packs supplied by Rockwell Automation.
- 3. Review the problems discussed in the Troubleshooting section of this manual to eliminate common problems.
- 4. If the problem persists, contact Rockwell Automation Customer Support at 440-646-5800.
- 5. Pack the UPS in its original packaging.
- 1609 UPS Dimensions