Retsch SM 100 - Manual (Page 21)

Technical data
21
Pos : 6. 2 / 00005 Übersc hrift en/1. Übersc hrift en/1 Tec hnisc he Dat en @ 0\ mod_1222344525522_9. doc @ 2407 @ 1 @ 1
4 Technical data
Pos : 6. 3 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 Eins atz der M asc hine bei besti mmungsgemäß er Ver wendung @ 0\ mod_1226476732248_9. doc @ 3243 @ 2 @ 1
4.1 Use of the machine for the intended purpose
Pos : 6. 4 / 00010 Bedienungsanlei tungen Kapit elsamml ung en/SM 100/ 0005 SM100 T echnisc he Daten/ 0535 SM100 Modul Zielgruppe Masc hi nent yp @ 3\ mod_1284973723946_9.doc @ 23584 @ @ 1
Target group: Operating companies, operators
Designation of machine model: SM 100
Pos : 6. 5 / 00010 Bedienungsanlei tungen Kapit elsamml ung en/SM 100/ 0005 SM100 T echnisc he Daten/ 0530 SM100 Modul Ei ns atz bei bes timmungsgemäß er Ver wendung @ 3\ mod_1284973723227_9.doc @ 23575 @ @ 1
This powerful cutting mill is used to grind elastic and fibrous products and product
mixtures in batches or continuously. In addition this device is fundamentally not
designed to grind wet or damp materials. The special moulding of the cutting tools
in conjunction with the drive produces fast, efficient grinding without the ground
material interrupting the procedure.
With the following special features
The new powerful grinding mill can successfully perform difficult grinding tasks
where other grinding mills fail. The device facilitates particularly effective
preliminary grinding of heterogeneous material mixtures such as waste or
electronic components. Analytical fineness can usually be achieved in one step.
The cutting mill can also be used successfully with a number of other materials.
The grinding material is only slightly warmed in the process so that the mill can
also be used for materials that are temperature sensitive.
Use with the large selection of sieves, hoppers and collecting vessels enables the
equipment to be adjusted to individual tasks.
– Fast, successive grinding by 18 spiral-shaped cutting plates distributed
round the rotor
– Parallel section rotor
– Cutting tools made from quality materials
– User-friendly with central locking and control panel
– Consistent reliability of all operational device components
– Diverse use possible due to device variations and wide range of accessories
– Powerful grinding thanks to 1,5 kW motor with high torque
– Can be cleaned very quickly due to the push-fit rotor
– Defined ultimate fineness through bottom sieves with mesh sizes of 0.25 -
20 mm
Pos : 6. 6 / 00004 War nhi nweis e/H 0007 H INWEI S Eins atz bereic h des G erätes 8 Stündiger @ 1\ mod_1236240219096_9. doc @ 7693 @ @ 1
NOTICE
0T
Area of use of the machine
–
0T
This machine is a laboratory machine designed for 8-hour single-shift
operation.
•
0T
This machine may not be used as a production machine nor is it
intended for continuous operation.
Pos : 6. 7 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 Emmisionen @ 0\ mod_1226487095021_9. doc @ 3310 @ @ 1
4.2 Emissions
Pos : 6. 8 / 00004 War nhi nweis e/ V0044 VORSICHT Gehörs chaden (GM 300, SM 200, SM 300) @ 1\ mod_1248181519795_9.doc @ 11731 @ @ 1