Retsch Cryomill - Manual (Page 48)

Working instructions
48
Pos : 7. 2 / 00005 Übersc hrift en/1. Übersc hrift en/1 Ar beit s weis e @ 0\ mod_1226910058402_9.doc @ 3661 @ @ 1
6 Working instructions
Pos : 7. 3 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 Allgemei nes @ 0\ mod_1226913421529_9. doc @ 3723 @ @ 1
6.1 General
Pos : 7. 4 / 00010 Bedienungsanlei tungen Kapit elsamml ung en/Cr yoMill I I/ 0008 Ar bei ts weis e/ 0001 Cr yoMill II M odul Allgemeines @ 5\ mod_1343830265008_9.doc @ 33411 @ @ 1
The CryoMill is an extremely modern, efficient product from Retsch GmbH.
Due to the large selection of accessories, the CryoMill has a wide range of
potential applications in industrial and research laboratories.
It is primarily deployed in the chemical and pharmaceutical area, in mineralogy and
biology etc.
Pos : 7. 5 / 00004 War nhi nweis e/ V0004 VORSICHT Expl osi ons- oder Brandgef ahr Ver mahlen @ 1\ mod_1236238455830_9.doc @ 7626 @ @ 1
CAUTION
2.V0004
Risk of explosion or fire
Changing sample properties
–
Consider that the properties and therefore also the hazardousness of your
sample can change during the grinding process.
• Do not use any substances in this device which carry the risk of
explosion or fire.
Pos : 7. 6 / 00004 War nhi nweis e/ V0006 VORSICHT Gefahr von Personens chäden Gefährliche St off e @ 1\ mod_1236238456269_9. doc @ 7634 @ @ 1
CAUTION
Danger of personal injury
Dangerous nature of the sample
–
Depending on the dangerous nature of your sample, take the
necessary measures to rule out any danger to persons.
• Observe the safety guidelines and datasheets of your
sample material.
Pos : 7. 7 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 D er Mahl vorgang @ 0\ mod_1226910105487_9.doc @ 3667 @ @ 1
6.2 The grinding process
Pos : 7. 8 / 00010 Bedienungsanlei tungen Kapit elsamml ung en/Cr yoMill I I/ 0008 Ar bei ts weis e/ 0004 Cr yoMill II M odul M ahl vorgang @ 5 \ mod_1343830267351_9. doc @ 33444 @ @ 1
• Insert your grinding jar filled with grinding sample and grinding ball/s into the
grinding jar support as described in the chapter " Inserting the grinding jar”.
• Close the hood.
• Set the grinding parameters.
• Open your external liquid nitrogen supply line.
• Start the device.
Do not open the hood during the grinding process.
The grinding jars are brought to a halt immediately by the built-in brake, however
the grinding process can no longer be continued with the remaining grinding time.
The device must be restarted. The original parameters are available here.
Pos : 7. 9 / 00005 Übersc hrift en /1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 M ahlgut mengen und Aufgabe- Kor ngröß en @ 0\ mod_1226913488592_9.doc @ 3729 @ @ 1
6.3 Quantities of sample material and feed sizes
Pos : 7. 10 /00010 Bedi enungsanleit ung en Kapitels ammlungen/Cr yoMill II /0008 Arbeits weis e/ 0003 Cr yoMill I I M odul M ahlgut menge und Korngröß en @ 5\ mod_1343830266570_9. doc @ 33433 @ @ 1
Recommended ball filling (unit)