MTS Series 685 Hydraulic Grip Supply User Manual
Page 31
Series 685 Grip Supply Installation Procedure
Series 685 Grip Supply Product Information
Installation
31
4. Remove the 1/2 inch NPT plug.
The plug was installed in the top of the reservoir for shipment from the
factory.
5. Check the fluid in the reservoir.
The reservoir contains 8.3 liters (2.2 gallons) when the fluid is up to the
“High” mark on the sight gage and 6.1 liters (1.6 gallons) when the level is
at the “Low” mark.
Add fluid to the reservoir as necessary to bring the fluid level to or near the
“High” mark on the sight gage. An extra gallon is shipped with the
hydraulic grip supply. Never add another fluid other than Mobil 525 SHC to
the reservoir.
6. Install the breather.
100 V / 50 Hz / 1 phase
100 V
Common
110 V / 50 Hz / 1 phase
110 V
Common
200 V / 50 Hz / 1 phase
200 V
Common
220 V / 50 Hz / 1 phase
220 V
Common
240 V / 50 Hz / 1 phase
240 V
Common
C
USTOMER
-S
UPPLIED
P
OWER
L1
L2
Sight gage
NPT/Breather
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)