Koolance ERM-3K3UC-R - Manual (Page 7)

6 7 User Manual System Features
PUMP SET
The pump speed can be manually set from 1-10:
PUMP(1-10) 7LV : Pump Speed Level
The pump speed level will flash. Press ▼ or ▲ to adjust. Press
◙
to return to the
previous menu.
FLOW SET
If a Koolance flow meter (sold separately) has been connected to the slot interface
adapter, configuration is needed to properly display its values. Only one flow meter
can be displayed by the cooling system.
FLOW METER SET
FM-17 ID: 10mm : Flow Meter Model, Tubing Internal Diameter
The Koolance flow meter model number (SKU) will flash. Press ▼ or ▲ to adjust
this based on the following:
• INS-FM16: change to “FM-16”
• INS-FM17, INS-FM17N, INS-FM18: change to “FM-17”
Press
◙
to move to the next option. The tubing internal diameter (ID) size will
flash. This refers to the hose size attached to the flow meter itself. Press ▼ or ▲
to adjust this based on the following:
• 6mm (1/4 inch): change to “ID: 6mm”
• 10mm (3/8 inch): change to “ID: 10mm”
• 13mm (1/2 inch): change to “ID: 13mm”
Press
◙
to return to the previous menu.
DISPLAY SET
The display settings configure which values you wish to appear on the front display
and how they are shown:
DISPLAY
FIXED
CYCLIC : Show 2 values or cycle multiple values
The first option, “FIXED”, will flash. Press ◄ or ► to change between these
options. Press
◙
to configure one of the selections, or press ▲ to exit. If “FIXED”
is selected, two lines will be shown:
TEMP1 21.7C : First line display option
TEMP1 21.7C : Second line display option
The first line will flash. Press ▼ or ▲ to change what this line will display:
TEMP1 21.7C : Show temperature sensor #1
TEMP2 21.2C : Show temperature sensor #2
TEMP3 20.8C : Show temperature sensor #3
FAN1 1770RPM : Show fan channel #1
FAN2 1640RPM : Show fan channel #2
FAN3 1820RPM : Show fan channel #3
PUMP 5730RPM : Show pump speed
FLOW 4.1LPM: Show flow rate
Press
◙
to confirm. The second line will flash. Press ▼ or ▲ to adjust this line.
Press ◄ to return to the previous menu, or press
◙
to return to the main screen.
When “FIXED” is the chosen display option, line 1 and 2 can be changed quickly
without reentering the DISPLAY SET menu. To do this, briefly press
▲ from the
main screen. The first line will flash:
TEMP1 21.7C : First line display option
PUMP 5400RPM : Second line display option
Press ▼ or ▲ to change what this line will display among the options described
earlier. Press
◙
to move to line 2, and similarly use ▼ or ▲. Press
◙
again to
exit.
If “CYCLIC” is chosen from the DISPLAY SET menu, multiple values will be rotated
through the front display. The first option is whether these values will cycle vertically
or horizontally through the display:
CYCLIC
VERT HORI: Rotate values vertically or horizontally
The first option, “VERT”, will flash. Press ◄ or ► to change between these options,
press
◙
to configure a selection, or press ▲ to exit. Choosing either option with
◙
will list all available values:
*TEMP1 21.7C : Show temperature sensor #1
*TEMP2 21.2C : Show temperature sensor #2
*TEMP3 20.8C : Show temperature sensor #3
*FAN1 1770RPM : Show fan channel #1
*FAN2 1640RPM : Show fan channel #2
*FAN3 1820RPM : Show fan channel #3
*PUMP 5730RPM : Show pump speed
*FLOW 4.1LPM: Show flow rate
▲
▼
▲
▼