Koolance CPU-370SI-R - Manual

Install two G 1/4 BSP threaded nozzles (sold separately) into
the cooling block. Hand tighten all nozzles-- overtightening
can damage the block and threads.
CAUTION: Be sure to attach a Koolance system temperature probe
(if available) to the CPU cooler during installation. Koolance system
safety features may not function properly without the correct placement
of this probe, and hardware damage can result.
!
CPU-370SA, CPU-370SI Installation Guide v 1.0
1
4
Remove any protective film from
the bottom of the cold plate.
Trim out a piece of metal tape and apply it to keep the
temperature probe in place. DO NOT stick metal tape or
the temperature probe where the processor comes in
contact with the cooler.
You can use a zip-tie to further secure the temperature
probe wire to the water block’s tubing.
DO NOT attempt to install the temperature probe in
between the processor and cooler. Despite its thin size, it
will interfere with CPU contact or burn-out the sensor.
If a Koolance system is used,
place the temperature sensor
included with it on the edge or
side of the water block’s metal
cold plate. Make sure it is not
covering any area that will be
in contact with the CPU.
The CPU water block can be opened (for cleaning,
etc.) by carefully unscrewing the four assembly screws with the
included wrench. It is extremely important to reassemble this
product properly. WHEN REASSEMBLING, CAREFULLY HAND-
TIGHTEN THE ASSEMBLY SCREWS AND DO NOT OVER-
TIGHTEN. IF DONE IMPROPERLY, THE ACETAL THREADS
CAN BECOME STRIPPED OR CROSS-THREADED!
Reassembly:
1. Make sure both o-rings are smoothly
in their grooves. These should never
become warped or damaged.
2. The center impingement plate has
notched corners to align it with tabs on
the top cover.
1. 1. 2. 2.
3. The cold plate microfins must run
perpendicular to the impingement plate
center slot!
4. When the block is assembled, look
into the outlet hole to confirm proper
fin direction. The microfins should run
towards the inlet hole.
3. 3.
4. 4.
CPU-370SA Mounted CPU-370SI Mounted
Keep-
Out
Area
2
3
(CPU-370SA only) Some processors, like
AMD sockets AM2/AM2+/AM3, may require
removal of the motherboard’s existing retention frame in order
to install the Koolance water block.
If present, remove this retention frame by unscrewing its
screws, or if plastic tabs are used, pulling out these locking
tabs.
Threaded posts are screwed directly into the
CPU block’s rear bracket. (NOTE: Socket
2011 is an exception, simply screw the matching posts
directly into the motherboard back plate.) Pliers or a small
wrench may be required to fully tighten the posts.
Place the rubber insulation pad over the bracket posts. This
helps to protect the motherboard from damage and electrical
shorting from the back plate.
AMD Socket
AM2, AM2+, AM3
From beneath the CPU socket, carefully insert the
back plate posts through the motherboard mounting
holes. The insulating pad will be sandwiched between
the back plate and motherboard.
(Refer to bracket images on the following page for specific
CPU post positioning.)
One or two back plates may be included with your water block. Use the below
diagrams to determine which holes your mounting posts must use.
Intel Socket
LGA 1156, 1155 Intel Socket
LGA 1366
Intel Socket
LGA 775
Apply thermal paste to the CPU directly. Spread the paste
so that it evenly and thinly covers the CPU. A piece of thick
paper (such as a business card) works well for this.
Place the water block over the mounting posts.
The temperature sensor should already be
installed on the cooler (if available).
Install the optional plastic washers over each
post. These help protect the CPU block from
getting scratched.
Place the tension springs onto each post.
Place thumb nuts onto each post and gradually
tighten by hand in a cross-shape pattern. DO NOT
OVERTIGHTEN THUMB NUTS OR DAMAGE
TO THE WATER BLOCK, PROCESSOR, OR
MOTHERBOARD COULD RESULT!
NOTE: For Intel socket
LGA 2011, use mother-
board’s back plate.