Klein Tools MM1300 - Manual

cuStoMEr SErVIcE
KLEIN tooLS, INc.
450 Bond Street
Lincolnshire, IL 60069
1-877-775-5346
[email protected]
www.kleintools.com
139713 Rev. 03/14 B
ENGLISH
Instruction Manual
• auto /
MaNuaL
raNGE
• auto HoLD
• MaX / MIN
• Bar GrapH
• BacKLIGHt
• LEaD
HoLDEr
• 3-5/6 DIGIt
6000 couNt
LcD
ENGLISH
8. temperature:
Features:
SYMBoLS uSED oN LcD
~
ac Measurement Dc Measurement
-
Negative Dc Value AT auto range active
O.L. overload: range Exceeded Apo auto power-off active
Low Battery HoLD Hold active
MIN Minimum reading MAX Maximum reading
% Duty cycle Mode Frequency Mode
V Voltage Measurement A current in amps
Ω resistance in ohms Diode test
F capacitance in Farads continuity test
relative / Zero Mode n Nano 10 -9
µ Micro 10 -6 m Milli 10 -3
k Kilo 10 3 M Mega 10 6
°F Degrees Fahrenheit °C Degrees celsius
a-HoLD auto-Hold active
ELEctrIcaL SpEcIFIcatIoNS
Dc Voltage Measurement
range resolution accuracy
600mV ˜ 600V 0.1mV ˜ 0.1V ± (0.5% + 4 digits)
1000V 1V ± (0.8% + 10 digits)
overload protection: 1000V Input Impedance (Nominal): 10MΩ, <100pF
ac Voltage Measurement
range resolution accuracy
600mV 0.1mV
± (0.75% + 5 digits)
6V ~ 600V 1mV ~ 0.1V
1000V 1V ± (1.0% + 8 digits)
overload protection: 1000V RMS Input Impedance (Nominal): 10MΩ, <100pF
Frequency response: 40 to 400 Hz response: Averaging
Dc current Measurement
range resolution accuracy
600µA ~ 400mA 0.1µA ~ 0.1mA ± (1.0% + 5 digits)
6A ~ 10A 1mA ~ 10mA ± (1.5% + 5 digits)
overload protection:
• µama: F440mA/1000V fuse
• a Input: F11A / 1000V fuse
ac current Measurement
range resolution accuracy
600µA ~ 400mA 0.1µA ~ 0.1mA ± (1.5% + 5 digits)
6A ~ 10A 1mA ~ 10mA ± (2.0% + 5 digits)
overload protection: µama: F440mA/1000V fuse / a Input: F11A / 1000V fuse
Frequency: 40 to 400Hz response: Averaging
resistance Measurement
range resolution accuracy
600 Ω ˜ 6MΩ 0.1 Ω ˜ 0.001MΩ ± (1.0% + 5 digits)
60M Ω 0.01M Ω ± (1.5% + 10 digits)
overload protection: 600V RMS
capacitance Measurement
range resolution accuracy
60nF 0.01nF
± (3.5% + 6 digits)
600nF ~ 6000µF 0.1nF ~ 1µF
overload protection: 600V RMS
Frequency Measurement
range resolution accuracy
99.99Hz ˜ 499.9kHz 0.01Hz ˜ 0.1kHz ± (0.1% + 3 digits)
overload protection: 600V RMS Sensitivity: >0.7V RMS
Duty cycle Measurement
range resolution accuracy
0.1 ˜ 99.9% 0.1% ± (0.2% per kHz + 0.1% + 5 digits)
overload protection: 600V RMS Sensitivity: < 50V
Frequency range: <10kHz
Diode test
overload protection range test current open circuit Voltage
600V RMS 6.0V Appx. 0.25mA < 1.8V DC (typ.)
continuity test
overload protection open circuit Voltage threshold (appx.)
600V RMS < 0.44V <40 Ω
temperature Measurement
range resolution accuracy
-58 ~ 600°F 0.1°F ± (1.0% + 5.4°F)
-50 ~ 600°C 0.1°C ± (1.0% + 3.0°C)
600 ~ 1832°F 1°F ± (1.0% + 5.4°F)
-600 ~ 1000°C 1°C ± (1.0% + 3.0°C)
overload protection: 600V RMS
thermocouple accuracy: Not specified
Specifi cations subject to change
7. capacitance: < 6000µF
Features: HoLD
Safely discharge capacitor before measurement.
• Reading may take up to 60 seconds for large capacitors.
Do Not apply voltage to thermocouple.
• -58° to 1832°F (-50° to 1000°C)
testing Fuses:
• When selecting µA or mA/A functions the meter will indicate
“LEad” if the test leads are not properly connected to the meter.
• Note: This message remaining on the screen after properly
connecting the test leads is an indication that the fuse is open.
MaX/MIN HoLD rEL a- HoLD
6. Frequency (Hz) / Duty cycle <500kHz
Features:
HoLD
WarraNtY
www.kleintools.com/warranty
cLEaNING
Clean the instrument by using a damp cloth. Do not use abrasive cleaners
or solvents.
Take care to keep the sensor lens clean at all times. Clean the lens using a soft
cloth or cotton swab with water or rubbing alcohol only, and allow the lens to
dry before use.
StoraGE
Remove the batteries when instrument is not in use for a prolonged period of
time. Do not expose to high temperatures or humidity. After a period of storage
in extreme conditions exceeding the limits mentioned in the Specifications
section, allow the instrument to return to normal operating conditions before
using it.
DISpoSaL / rEcYcLE
Do not place equipment and its accessories in the trash. Items
must be properly disposed of in accordance with local regulations.
1000V
10A
Dwg Name: MM1300-139713ART Dwg No: 139713
ECO No: 16082 Pkg Dwg Ref: 1650 Rev: B
Color Reference: N/A
PRESS
PRESS
MM 1300
MM1300 Instruction Manuals - MASTER.indd 1-4 3/12/2014 10:16:56 AM