Gamber-Johnson MCS-ERGOBOX12 - Manual

INSTALLATION INSTRUCTIONS
Product Revision Form #
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
12" Ergonomic Console Box & Accessories
MCS-ERGOBOX12
Rev D INST-284
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
The purpose of this instruction sheet is to illustrate the manufacturer's recomended method for installing the
MCS-ERGOBOX12.
MCS-ERGOBOX12 is a descrete solution for mounting various mobile communication control
heads. Included with the MCS-ERGOBOX12 is one set of short Faceplate Vertical Offsets. Due to a shallow depth in
the front end of the console box, these Faceplate Vertical Offsets must be used in place of the Vertical Offsets that come
with Gamber-Johnson Faceplate Kits (see INST-3).
1. When installing the MCS-ERGOBOX12 onto a
Gamber-Johnson MCS Top Plate, insert and loosely
assemble four 1/4-20 carriage bolts, four 1/4" Dia.
washers, four 1/4" lock washers and four 1/4-20 hex
nuts about the desired mounting slots in the bottom of
the box (see FIG. 1). Orient the head of the carriage
bolts below the box.
2. Insert the four heads of the carriage bolts into the
desired corresponding key holes (see FIG. 1) on the
MCS-Top Plate until the bolt heads drop below the
Top Plate. If the chosen mounting slots do not line
up with the key holes on the Top Plate it will be
necessary to assemble the hardware about the box
and the Top Plate at the same time. Place box in
desired position and tighten hardware.
Accessories
The MCS-ERGOBOX12 has many accessories that are designed to attach to the
exterior of the box. The next few sections of this instruction sheet are dedicated to
illustrating how to attach the various accessories.
3. Due to the shallow depth of the face nearest the
vehicle occupants (see FIG. 3), as compared to the
MCS-Epic console box series, it is necessary to replace
the standard Vertical Offsets with a set of shorter
Vertical Offsets (1 set is included with the
MCS-ERGOBOX12). The radio/radio head in the
lowest position on the box will require the Short
Vertical Offset. Follow instruction sheet INST-3 for
assembly and installation instructions, substituting the
short Faceplate Vertical Offsets (see FIG. 2) with the
Vertical Offsets that come with Gamber-Johnson
Facplate Kits.
Cup Holder (MCS-CUP2)
1. The cup holder is designed to mount to either
the short, front face of the MCS-ERGOBOX12
or directly to an MCS Top Plate. There are two
10-32 x .375 Phillips Pan Head screws included
to attach the cup holder to the box (see FIG. 3)
FIG. 2
KEY HOLES
FIG. 3
FRONT FACE
SHEET 1 OF 3
MCS TOP PLATE
MOUNTING
SLOTS
FIG. 1
© copyright 2012 Gamber-Johnson, LLC