Pro control – Auto Meter 5677 User Manual
Page 4
The Super Bezel is a registered trademark of Auto Meter Products, Inc.
12 MONTH LIMITED wARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the
original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product
failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of
the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter
must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in
duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter
Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
SERvICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you
need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be
added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
FOR SERVICE SEND TO: AUTO METER pRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (866) 248-6357
Email us at [email protected]
http://www.autometer.com
2650-1458-00 7/7/09
© 2009 Auto Meter Products, Inc.
pro Control
The Pro Control feature activates a switched ground output at a user defined set point. Pro Control can be used to switch on a relay to activate
ignition kill, cooling fans, lamps, alarms, etc. The set points define three regions on the gauge dial, the region below the low set point, between the
set points, and above the high set point.
warning: Pro Control outputs shall not
exceed 2.0 amps at 12 volts
REgION A
REgION b
HIgH
REgION C
LOw
Low Set Point - ACTIVE STATE LOW (orange wire)
Pointer region
Pro Control output
#1
normally open
Contact
normally Closed
Contact
Dial Color
a
active (on)
CLoSeD (on)
oPen (oFF)
Low warn Color
B
oFF
oPen (oFF)
CLoSeD (on)
Backlight Color
C
oFF
oPen (oFF)
CLoSeD (on)
High warn Color
Low Set Point - ACTIVE STATE HIGH (orange wire)
Pointer region
Pro Control output
#1
normally open
Contact
normally Closed
Contact
Dial Color
a
oFF
oPen (oFF)
CLoSeD (on)
Low warn Color
B
active (on)
CLoSeD (on)
oPen (oFF)
Backlight Color
C
active (on)
CLoSeD (on)
oPen (oFF)
High warn Color
High Set Point - ACTIVE STATE HIGH (BLue wire)
Pointer region
Pro Control output
#2
normally open
Contact
normally Closed
Contact
Dial Color
a
oFF
oPen (oFF)
CLoSeD (on)
Low warn Color
B
oFF
oPen (oFF)
CLoSeD (on)
Backlight Color
C
active (on)
CLoSeD (on)
oPen (oFF)
High warn Color
High Set Point - ACTIVE STATE LOW (BLue wire)
Pointer region
Pro Control output
#2
normally open
Contact
normally Closed
Contact
Dial Color
a
active (on)
CLoSeD (on)
oPen (oFF)
Low warn Color
B
active (on)
CLoSeD (on)
oPen (oFF)
Backlight Color
C
oFF
oPen (oFF)
CLoSeD (on)
High warn Color
+12v
Pro Control Low
Output (#1)
(Switched Ground)
Pro Control
Ground Neg. (-)
Relay: Dedenbear Part # HPR
87A
87
85
86
30
+12v
87A
87
85
86
30
Pro Control High Output (#2)
(Switched Ground)
Normally
Closed
Normally
Open
ORANGE
BLACK
BLUE
Normally
Closed
Normally
Open
5 4 3 2 1
10 9 8 7 6
ExAmPLE