beautypg.com

Auto Meter 1110 User Manual

5" electric quad gauges, Mounting, Voltmeter

background image

OIL

FUeL WATeR

+12V gND

LAMP

Do not touch ignition wire to the sender terminal on

back of gauge or the sender will be damaged.

CAUTION:

INSTALLATION INSTRUCTIONS

3

3

8

" & 5" eLeCTRIC QUAD gAUgeS

2650-1178             

Mounting

Mount a 3 

3

8

" gauge in a 3 

3

8

" dia. hole and a 5" gauge in 

4 

5

8

" dia. hole in the dashboard. Fasten with brackets supplied 

as shown. (electrical wire for installation not included.)

To assure proper functioning of this instrument, please read 

instructions thoroughly before installing. 

1.  Gauge  connects  to  240-33  ohm  fuel  sender 

(3262), supplied in Quad gauge/Speedometer 

kit. Sender is not included in individual Quad 

gauges. The 3262 or comparable 240-33 ohm 

sender will be required. Route proper length 

of  18  gauge  wire  from  fuel  tank  to  gauge. 

Connect one end to terminal post on fuel level 

sender and the opposite end to the spade ter-

minal labeled “FUEL” on back of gauge. See 

illustration.

Voltmeter

1. Using 18 gauge wire, route wire through firewall using 

grommet. Attach one end to the negative GND (-) 

spade terminal on back of gauge, and the opposite 

end to a good engine ground. See illustration at right.

2. Attach one length of wire to the positive  +12V spade 

terminal on back of gauge and opposite end to +12V 

terminal on ignition switch or other switched +12V 

power source.

To 12V Terminal on Ignition 

Switch or other 12V source.

Step 1

1. Disconnect negative (-) battery cable.

Step 2

Fuel Level

Step 3

Do not touch ignition wire to the sender terminal on

back of gauge or the sender will be damaged.

CAUTION:

PASSeD

MODeL NUMBeR

DATe OF MANUFACTURe

OIL

FUeL WATeR

+12V gND

LAMP

Connect to terminal post 

on fuel tank sender.

Grommet

Ground

5" Models

4

15

16

"

2

3

8

"

4

19

32

"

Grommet

CAUTION!

As a safety precaution the Red wire of this product should 

be fused before connecting it to the positive (+) side of 

the 12V DC battery. We recommend using a 4 Amp, 3AG 

fast-acting type cartridge fuse (Littlefuse® # 312 004 or 

an equivalent) inline with the Red wire of our product. 

3

3

8

" Models

3

11

32

"

2

1

4

"

3

3

4

"

5" Models

3

3

8

" Models

NOTe: Some late model vehicles use electronic sensors in their 

pressure and temperature senders for engine control func-

tions. Before removing the original sender, we recommend 

that you contact your automotive dealer to be sure no 

critical functions will be disrupted. With pressure gauges 

it is beneficial to add a T-fitting to install your new gauge 

and to keep the warning light operational. This allows you 

to monitor the pressure and still have a warning light to 

indicate emergency conditions. The ground, fuel sender, 

temperature sender, and oil sender wires should be routed 

through fire wall using the supplied grommet.

QUeSTIONS

:

If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s), 

please contact Auto Meter Technical Service at 815-899-0801. You may also email us at [email protected].

Additional information can also be found at http://www.autometer.com

This manual is related to the following products: