Auto Meter 1785 - Manual

FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 or
Email us at [email protected] 2650-655E 4/8/03
12 MONTH LIMITED WARRANTY
The manufacturer warrants to the consumer that this product will be free from defects in materials and workmanship for a period of twelve (12) months from the date of the original purchase. Products
that fail within this 12 month warranty period will be repaired or replaced at the manufacturer’s option to the consumer, when determined by the manufacturer that the product failed because of defects
in material or workmanship. This warranty is limited to the repair or replacement of parts in the instrument and the necessary labor done by the manufacturer to affect the repair or replacement of the
instrument. In no event shall this warranty exceed the original purchase price of the instrument, nor shall the manufacturer be responsible for special, incidental or consequential damages or costs
incurred due to failure of this product. Warranty claims to the manufacturer must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original
purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident,
water damage, abuse, unauthorized repairs or alterations voids this warranty. The manufacturer disclaims any liability for consequential damages due to breach of any written or implied warranty on all
products made by the manufacturer.
INSTALLATION INSTRUCTIONS
2
1
/
16
" ELECTRIC CLOCkS
®
2650-655E
Lens Cleaning
The clear lens on your clock
is made of acrylic plastic. To
prevent scratching caution
must be used when cleaning.
Use a mild, soapy solution and
soft cloth to clean. Wipe lightly.
INSTALLATION
To Good
Ground
Grommet
Twist- In
Light Socket
2 1 ⁄
16
”
Thumbnut
and Lockwasher
To 12 volt terminal
on ignition switch
or to any constant
12V power source.
1. Disconnect negative (-) battery cable.
2. Mount gauge into dash or panel using mounting bracket
and hardware provided.
3. Using 18 gauge wire and female spade connector
(not provided). Attach female spade connector to the
negative (-) spade terminal on back of gauge and the
opposite end to a good engine ground.
4. Attach second wire to the positive (+) female spade
connector on back of gauge and the opposite end to 12
volt terminal on ignition switch or to any constant 12V
power source.
5. Reconnect negative (-) battery cable.
NOTE: To set clock, push in the set knob and turn
clockwise to the current time. When time is set,
make sure that the knob is in the out position
for proper operation.
Mounting
These gauges can be mounted in a 2 1 ⁄ 16 ” dia. hole or in a
standard aftermarket street rod panel. Fasten with brackets
supplied as shown. (Hookup wire is required.) To assure
proper functioning of this instrument, please read instructions
thoroughly before installing.
FRONT MOUNTING
(SIDE VIEW)
To 12 volt terminal
on ignition switch
or other switched
12 volt source.
To Good
Ground
Replace light bulb with the same bulb
number that was removed.
CAUTION!
As a safety precaution the Red wire of this product
should be fused before connecting it to the positive
(+) side of the 12V DC battery. We recommend
using a 4 Amp, 3AG fast-acting type cartridge fuse
(Littlefuse® # 312 004 or an equivalent) inline with
the Red wire of our product.
© 2003 Auto Meter Products, Inc.
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you
need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be
added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
CAUTION!
As a safety precaution the Red wire of this product should be fused before connecting it to the
positive (+) side of the 12V DC battery. We recommend using a 4 Amp, 3AG fast-acting type
cartridge fuse (Littlefuse® # 312 004 or an equivalent) inline with the Red wire of our product.