beautypg.com

Oil pressure water temperature, Step 4, Step 5 – Auto Meter 1110 User Manual

Page 2: Lighting (5" models only) step 6, Step 7, Lighting (3, Models only), 5" models 3, Models

background image

FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 or

Email us at [email protected]

12 MONTH LIMITeD WARRANTY

The manufacturer warrants to the consumer that this product will be free from defects in materials and workmanship for a period of twelve (12) months from the date of the original purchase. Products 

that fail within this 12 month warranty period will be repaired or replaced at the manufacturer’s option to the consumer, when determined by the manufacturer that the product failed because of defects 

in material or workmanship. This warranty is limited to the repair or replacement of parts in the instrument and the necessary labor done by the manufacturer to affect the repair or replacement of the 

instrument. In no event shall this warranty exceed the original purchase price of the instrument, nor shall the manufacturer be responsible for special, incidental or consequential damages or costs 

incurred due to failure of this product. Warranty claims to the manufacturer must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original 

purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, acci-

dent, water damage, abuse, unauthorized repairs or alterations voids this warranty. The manufacturer disclaims any liability for consequential damages due to breach of any written or implied warranty 

on all products made by the manufacturer.

GND
S I

1. Install water temperature sender. Remove stock 

sender for water temperature indicator light and 

install new sender.

  Sender should automatically be grounded when 

installed. If not, proper ground connections should 

be made.

2. Route 18 gauge wire through firewall using grom-

met. Connect one end to the terminal post on 

sender and opposite end to spade terminal labeled 

“WATER” on back of gauge. See illustration below.

Oil Pressure

Water Temperature

TeMPeRATURe SeNDeR

PReSSURe

SeNDeR

No. 2242 for Domestic 

Cars with 

1

8

"

 NPT 

Outlet. Ford uses 

1

4

"

NPT Adapter included.

CAUTION!

As a safety precaution the Red wire of this product should be 

fused before connecting it to the positive (+) side of the 12V 

DC battery. We recommend using a 4 Amp, 3AG fast-acting 

type cartridge fuse (Littlefuse® # 312 004 or an equivalent) 

inline with the Red wire of our product. 

   

SeRVICe

For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you 

need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will 

be added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.

© 2006 Auto Meter Products, Inc.

2650-1178       7/18/06

PASSeD

MODeL NUMBeR

DATe OF MANUFACTURe

OIL

FUeL WATeR

+12V gND

LAMP

OIL

FUeL WATeR

+12V gND

LAMP

Grommet

Step 4

Grommet

Step 5

Do not touch ignition wire to the

sender terminal on back of gauge or

the sender will be damaged.

CAUTION:

Dash lighting or 

+12V power supply

Lighting (5" models only)

Step 6

1. Connect one wire to dash lighting 

circuit or to other 12V power source 

and opposite end to spade terminal 

labeled “LAMP” on back of gauge.

Step 7

1. Reconnect negative (-) battery cable.

Do not touch ignition wire to the sender terminal on

back of gauge or the sender will be damaged.

CAUTION:

5" Models

3

3

8

" Models

5" models only

FUEL

OIL

+12V GND LAMP

WATER

BLACK

BLACK

TO GROUND (-) NEGATIVE

WHITE

WHITE

DASH LIGHTING 

CIRCUIT OR 12V (+)

1. Connect white wire to 

dash lighting or to other 

+12V power supply .

  Connect black wires to 

negative ground source.

Lighting (3

3

8

"

models only)

1. Remove stock sender for dash warning light and install 

gauge adapter. Sender fits 

1

8

" NPT and comes with 

1

4

" NPT 

adapter. Sender should automatically be grounded when 

installed. If not, proper ground connections should be made.

2. Route 18 gauge wire through firewall using grommet. 

Connect one end to terminal post on pressure sender, and 

opposite end to the spade terminal labeled “OIL” on back of 

gauge. See illustration above.

This manual is related to the following products: