Auto Meter 3674 - Manual (Page 2)

power-Up
The pointer will move backward to the stop pin and then move to the zero box. This procedure is an auto-calibration
function and is performed on every power-up. While this test is being performed, the gauge may make a clicking
sound. This is normal.
12 MONTH LIMITeD wARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the
original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product
failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of
the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter
must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in
duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter
Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
SeRVICe
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you need the product
back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be added to the cost of “RUSH
REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
FOR SERVICE SEND TO: AUTO MeTeR pRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (866) 248-6356
Email us at [email protected]
http://www.autometer.com
2650-1134-00 Rev. B 3/14/08
Installation - Brake pressure
Brake Line Brake Fitting
Teflon Sealing compound
Pressure Sensor
1 ⁄
8
” NPT Thread on Sensor
© 2008 Auto Meter Products, Inc.
1. Check that you have all parts required for installation, and the
engine is cool.
2. Disconnect the negative (-) battery cable.
3. Gauge mounts in a 2 5 ⁄
8
” hole for 2 5 ⁄
8
” gauges, and a 2 1 ⁄
16
”
hole for 2 1 ⁄
16
” gauges. Use supplied brackets and nuts to
secure gauge to dash.
4. Drill 1” diameter hole where wires pass through sheet metal
(such as firewall) and install rubber grommet provided.
5. Connect the white wire to dash lighting or switchable 12V light
source, the red wire to switched +12V source and the black
wire to ground. (see diagram for details)
6. If you are not familiar with proper brake system bleeding
procedures, do not install this gauge. Have a qualified
mechanic do it for you.
7. Locate a 1 ⁄
8
” -27 NPT port in your brake system in a location
where you would like to measure brake pressure. If no port is
available, you will need to install a tee fitting in the brake line
you want to measure. Only use fittings that are approved for
use in brake systems.
8. Install the pressure sensor in the 1 ⁄
8
” -27 NPT port using a
Teflon thread sealing compound.
9. Bleed the brake system using standard brake bleeding
procedures.
Again, if you are not familiar with proper brake system
bleeding procedures, do not install this gauge. Have a
qualified mechanic do it for you.
Note: Install sensor with electrical connector
facing down to allow any air in the sensor
to escape during bleeding.
The Super Bezel is a registered trademark of Auto Meter Products, Inc.