Installation tips, Optional equipment – Advance Adapters 716806A User Manual
Page 10
![background image](/manuals/550989/10/background.png)
ADVANCE ADAPTERS INC.
P/N: 716806A
P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447
PAGE 10 OF 10
Telephone: (800) 350-2223
Fax: (805) 238-4201
Page Rev. Date:
07-09-13
SPECIAL NOTE:
The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.
Installation Tips
We recommend Weldless DD and Double Splined universal joints for the best steering system.
Weldless DD universal joint features two set screws for maximum holding power. Position yoke, tighten set screws to mark the shaft.
Remove yoke and drill the set point on the shaft. When installing the universal joint, set screws are tightened into the countersink
mark, then tighten the jam nut and the shaft will not move. We recommend the use of Loctite.
Spline both ends (3/4"-36) universal joint is the preferred design, as it allows the shaft to be rotated in small increments during
installation to properly align or phase the steering system. Once the steering is set, tighten set screws to mark the shaft. Remove
yoke and drill the set point on the shaft. When installing the universal joint, set screws are tightened into the countersink mark, then
tighten the jam nut and the shaft will not move. We recommend the use of Loctite.
A FEW NOTES
**
Phasing-Keep the forks of the yokes closest to each other in line and parallel to the centerline of the shaft to avoid binding.
**
Always use the minimum angle when designing your system - ideally 10 degrees or less, NEVER MORE THAN 35 DEGREES.
**
NEVER WELD a universal joint. Welding reduces the strength of the metal and can melt the needle bearing seal.
**
BUFFING creates a very attractive finish in a matter of minutes. It is very important not to buff the caps because over heating
may damage the bearing seals.
716863
- Collapsible Steering Shaft 3/4" DD X 1" DD
(comes without any universal joints)
716841
- Universal Joint (1" DD X 1"DD)
716843
- Universal Joint (1" DD X 7/8")
716844
- Universal Joint (3/4" DD X .800" 36 spline)
716845
- Universal Joint (1" DD X 3/4" 36 spline)
716846
- Universal Joint (1" DD X .800" 36 spline)
716848
- Universal Joint (3/4" DD X 1" 48 spline)
716849
- Universal Joint (3/4" DD X 1" DD)
716850
- Universal Joint (3/4" DD X 3/4" 36 spline)
716851
- Universal Joint (3/4" DD X 3/4" DD)
716852
- Universal Joint (3/4" 36 spline X 3/4" 36 Spline)
Optional Equipment
Steering Boxes & Pumps
716881-P
- Post 1980 Saginaw box.
O-RING FITTINGS
(3/4" 30 spline actuator)
716882
- Post 1980 Saginaw box.
O-RING FITTINGS
(3/4" 30 spline actuator)
716885-P
-Saginaw pump w/
O-RING fittings
716886-P
-Saginaw pump w/
o-ring/remote res.
716887-P
-Press Hose kit
716888-P
-Return Hose kit
POWER STEERING CONVERSION JEEP
UNIVERSAL(minus spud shaft & column yoke)